Onkyo TX-NR1007 Troubleshooting—Continued, Video There’s no picture, The picture is distorted

Troubleshooting—Continued

•With some CD and LD players, you won’t be able to playback DTS material properly even though your player is connected to a digital input on the AV receiver. This is usually because the DTS bitstream has been processed (e.g., output level, sampling rate, or frequency response changed) and the AV receiver doesn’t recognize it as a genuine DTS signal. In such cases, you may hear noise.

•When playing DTS program material, using the pause, fast forward, or fast reverse function on your player may produce a short audible noise. This is not a mal- function.

The beginning of audio received by an HDMI IN can’t be heard

•Since it takes longer to identify the format of an HDMI signal than it does for other digital audio sig- nals, audio output may not start immediately.

Video

There’s no picture

•Make sure that all video connecting plugs are pushed in all the way (page 24).

•Make sure that each video component is properly con- nected (pages 26 to 41).

•If your TV is connected to the HDMI output, set the “Monitor Out” setting other than “Analog” (page 47), and select “- - - - -” in the “HDMI Input Setup” on page 49 to watch composite video, S-Video, and com- ponent video sources.

•If your TV is connected to the COMPONENT VIDEO MONITOR OUT, S MONITOR OUT, or V MONI- TOR OUT, set the “Monitor Out” setting to “Analog” (page 47), and select “- - - - -” in the “Component Video Input Setup” on page 50 to watch composite video and S-Video sources.

•If the video source is connected to a component video input, you must assign that input to an input selector (page 50), and your TV must be connected to either the HDMI output or COMPONENT VIDEO MONI- TOR OUT (pages 26 and 30).

•If the video source is connected to an HDMI input, you must assign that input to an input selector (page 49), and your TV must be connected to the HDMI outputs (pages 26).

•While the Pure Audio listening mode is selected, the video circuitry is turned off and only video signals input through HDMI IN can be output.

•On your TV, make sure that the video input to which the AV receiver is connected is selected.

•If you selected “Both (Main)” or “Both (Sub)” in the “Monitor Out” setting, no picture may appear on your TV that is connected to a secondary HDMI output (not a priority HDMI output). In this case, change the set- ting to “Both” (page 47).

There’s no picture from a source connected to an HDMI IN

•Reliable operation with an HDMI-to-DVI adapter is not guaranteed. In addition, video signals from a PC are not guaranteed (page 26).

•When the “Monitor Out” setting is set to “Analog”, and the “Resolution” setting is set to anything other than “Through” (see page 48), no video is output by the HDMI outputs.

•When the “Resolution” (page 48) is set to any resolu- tion not supported by the TV, no video is output by the HDMI outputs.

•If the message “Resolution Error” appears on the AV receiver’s display, this indicates that your TV does not support the current video resolution and you need to select another resolution on your DVD player.

The onscreen menus don’t appear

•If your TV is connected to the analog outputs, set the “Monitor Out” setting to “Analog” (page 47).

•(European and Asian models) Specify the TV sys- tem used in your area in the “TV Format Setup” on page 54.

•On your TV, make sure that the video input to which the AV receiver is connected is selected.

The picture is distorted

•(European and Asian models) Specify the TV sys- tem used in your area in the “TV Format Setup” on page 54.

The immediate display does not appear

•If you select other than “Analog” in the “Monitor Out” setting (page 47), the immediate display will not appear when the input signal from the COMPONENT VIDEO IN is output to a device connected to the

COMPONENT VIDEO MONITOR OUT.

•Depending on the input signal, the immediate display may not appear when the input signal from the HDMI input is output to a device connected to the HDMI out- put.

Tuner

Reception is noisy, FM stereo reception is noisy, or the FM STEREO indicator doesn’t appear

•Relocate your antenna.

•Move the AV receiver away from your TV or com- puter.

•Listen to the station in mono (page 68).

•When listening to an AM station, operating the remote controller may cause noise.

•Passing cars and airplanes can cause interference.

•Concrete walls weaken radio signals.

•If nothing improves the reception, install an outdoor antenna.

149