Panasonic AW-F575E manual User Setting

Models: AW-F575E

1 38
Download 38 pages 43.26 Kb
Page 30
Image 30

USER SETTING

After setting the scene File Selection Switch (10) of the camera or (131)/(164) of RCU (RCB) to the USER SET position, the camera operating condition can be changed by the user to the desired condition

How to set the User Set Menu

1.Set the Scene File Selection Switch (10) of the camera or (131)/(164) of the RCU to the USER positlon.

SCENE USER A or SCENE USER B is displayed in the viewfinder.

Notes:

1The selection of USER A and USER B can be made by setting the Scene File Selection Switch

User Set Menus are shown in the following.

** Camera

Camera

to the USER pwtlon while pressing the Page Switch (13) or Check Button (25).

2. When only using the Scene File Selection Switch in the above procedure, the user file selected last will be dlsplayed

2.Set the User Set Switch in the side cover to position 1. The User Set Menu is displayed in the viewfinder

Set the User Set Switch in the side cover to position 2 The User Set Menu is also displayed on the monitor No.1 to No.8 menus can be dlsplayed by every press- ing the Page Switch and seting is available from Camera or Remote Control Unit side.

Menu Description

1.CONTRAST (LOW, MID, HI) (Contrast Level Setting) The Contrast (gamma) level can be selected

2.SHARPNESS (LOW, MID, HI)

(Sharpness Level Setting)

The sharpness (detail) level can be selected.

3.FLESH TONE (-2 - 2) (Flesh Tone Setting)

Flesh tone can be adjusted from -2 to 2 range in 5- step

4.CHROMA GAIN (-2 - 2) (Chroma Gain Setting)

The chroma gain can be selected from -2 to 2 range in 5-step.

5.PEAKING (Operating ratio Adjustment)

The ratio of AUTO IRIS/ELC detected peak to average can be adjusted in a range of 9 steps

6.AREA: ALL, CENTRE, TOP CUT, BOT CUT, R/L

CUT (Photometric Measurement Method Setting)

A photometric measurement method can be selected for AUTO lRIS/ELC

ALL: All the screen area is measured

CENTRE: The screen is measured mainly in the cen- tre area, approx. one-third each of the top and bottom and one third each of the right and left parts of the screen are cut out from measurement.

TOP CUT: Approx. one-third of the top part of the screen is cut out from measurement

BOT CUT: Approx. one-third of the bottom part of the screen is cut out from measurement

FUL CUT: Approx one-thtrd each of the right and left parts of the screen is cut out from measurement.

7.CLEAN DNR, OFF/LOW/HI

(Clean DNR (Digital Noise Reduction Switch)

The SIN ratio on the screen can be improved by thls switch.

Note: When the camera is operating alone, this func- tion can be made by the DNR Switch inside the camera

In this case, the display in the menu shows the set siwtch condition

8.LIGHTING: HALOGEN/FLUORESCENT/OUTOOOR

(Lighting Selection) (Only Scene 2) HALOGEN: Thls position is suitable for shooting

under halogen Iighting.

FLUORESCENT: This position is suitable for shooting under fluorescent Iighting

O U T O O O R : This position is suitable for shooting under outdoor lighting

After the setting is completed, set the User Set Switch to the OFF position

- 63 -

9.AUTO IRIS: ADJ ON/ADJ OFF

(Auto Iris Level Fine Adjustment)

When the mode is set to ADJ ON, fine adjustment of ALC/ELC convergence level can be made with the iris VR control on the RCU (RCB) if the camera is used with an RCU (RCB) and the iris mode is set to AUTO in the SETUP menu.

10.SHUTTER SW, ACTIVE, INHIBIT

(Shutter Active Inhibit Selection Switch)

When the INHIBIT position is selected, shutter function is not avallable even if the Shutter On/Off Switch is turned on

11.SHUTTER MODE, STEP/SYNCHRO/ELC (Shutter

Mode Setting)

STEP: Select this mode to set the shutter speed by the Step mode shutter setting

SYNCHRO: Select this mode for the fine adjustment of the shutter speed

ELC: Select this mode to control the electronic shutter speed automatically to regulate the amount of light.

12.STEP, 1/120, 2/250, 1/500, 1/1000, 1/2000, 1/4000,

1/10000 (Step Mode Shutter Setting)

When the Shutter Mode Setting is set to STEP, the shutter speed should be selected by this item

13.SYNCHRO, 50.0 - 250.4 Hz

(Synchro Mode Shulter Adjustment)

When the Shutter Mode Setting is set to SYNCHRO, the shutter speed can be adjusted by this item.

This mode can prevent the line noise when shooting the CRT dlsplay

14.FLD/FRM, FIELD/FRAME (Field/Frame Setting)

The FIELD means CCD field storage. The FRAME means frame storage, in which case vertical resolution increases

FIELD: Set to thls mode when shooting moving oblect

FRAME 1: Set to this mode when shootlng stlll object

FRAME 2: Set to this mode when better

resolution is

required

 

 

 

Note: It is recommended

that

FRAME

is normally

s e l e c t e d , because

t h e

residual image will

increase if field is selected

15.GAIN SW, 0/9/18, 0/12/24, 0/3/6, -6/0/12, -6/0/16dB (Gain Setting)

The HIGH/MID/LOW level of the High Gain Selection Switch can be set as shown below

Page 30
Image 30
Panasonic AW-F575E manual User Setting