Manuals / Panasonic / Home Audio / Stereo Receiver

Panasonic KX-VC500 manual Miscellaneous

Models: KX-VC500

1 98

Download 98 pages 49.26 Kb

Page 95

Miscellaneous

Additional Information

Message

Invalid DNS Server Address.

Connection will be closed in

nseconds.

Press "YES" to continue.

Note

•The message first appears when one minute remains and "60" is displayed for n. Then, the remaining time starts to decrease.

Cause and Solution

•The IP address contains an invalid value.

→Enter the IP address correctly. The correct format is XXX.XXX.XXX.XXX (dotted format decimal notation).

If the IP address contains 1 or 2 digit numbers, enter these numbers as they are. Do not enter like [.001].

Example: The IP address is [192.168.0.1].

–Correct entry: [192.168.0.1]

–Wrong entry: [192.168.000.001]

Multicast or broadcast addresses cannot be used.

•The time set for "Call Limit time" has one minute remaining. (Page 64)

→If you select "Yes", you can extend the call limit time for the amount set for "Call Limit time".

If you select "No", the call is disconnected.

Miscellaneous

Problem

"Safe Mode" is displayed on the screen.

Cause and Solution

•A standard definition (640 × 480p, 720 × 480p) video camera signal has been detected.

→Disconnect the video camera from the KX-VC500, and reset the KX-VC500 by turning off its power, then turning it back on. Check to make sure the video camera’s resolution is set to HD (1920 × 1080i), and then connect the video camera to the KX-VC500 again.

•A standard definition (640 × 480p, 720 × 480p) display signal has been detected.

→Disconnect the display from the KX-VC500, and reset the KX-VC500 by turning off its power, then turning it back on. Make sure to connect a HD (1920 × 1080i) display to the KX-VC500.

•The field frequency of the video camera or display you are using is different from the field frequency setting of the KX-VC500.

→Use a video camera or display that has the same field frequency as the KX-VC500. For details, contact your dealer.

Document Version 2010-10

Operating Manual

95

Image 95

Panasonic KX-VC500 manual Miscellaneous

Contents

Model No. KX-VC500 Operating ManualHD Visual Communication Unit Introduction Feature HighlightsEncrypted Communication TrademarksOpen Source Software Selectable Video Sourceapply PrecautionNotice for users in California contains perchlorate material—specialhandling mayBefore Operation Table of ContentsFor Your Safety Adjusting the Volume and ToneMiscellaneous Contacts and SettingsSpecifications InputGeneral For Your SafetyPower and Ground Connection Operating Safeguards Battery InstallationOperating Manual PowerInstallation BatteryOther Notes about OperationAbout the Operating Environment About Moving the DevicePreventing Data Disclosure Data SecurityPrivacy and Right of Publicity Preventing Data LossFCC Caution Federal Communications Commission RequirementsABC D EF G H Part Names and UsageMain Unit Front Main Unit Back Remote Control For Canada Users Boundary Microphone Optional AccessoryFederal Communications Commission Requirements Status LED PatternsScreen Standby LED patternOperating Manual PreparationDocument Version Connecting the KX-VC500 Microphones System Layout ExamplesDisplay and Main Video Camera 50 dBsplA Noise level Micro– phone40 dBsplA 45 dBsplAAmplifier/Active Speaker Connection Connecting the Display with a Component CableTurning the Power On/Off Home Screen Idle Screen Screen DisplayGuide Menu Screen Idle ScreenMain Video Camera Image Unit InformationVideo Image Video Conference Call ScreenOther party’s information Network Status Indication2Press One-TouchConnection 1 to Making a Video Conference Call1 Press Home • The Home screen is displayed4When you want to end the call, press End 2Select Contact List using and press Enter 1 45 2, 3 Starting a Video Conference 5When you want to end the call, press End4Press Start to start the call The Home screen is displayedExample: When using Input screen Calling by Entering an IP Address1 45 3 G: The screen will be switched to Input screen Incoming Call History Calling from the Call HistoryOutgoing Call History 1 45 2, The video conference begins Answering a Video Conference CallWhen Manual Answer is Set Document Version When Automatic Answer is SetStarting a Video Conference Operating Manual–G This Site: Layout 1Press Layout–B Other Site: Layout –R Both Sites: Layout each time you press Layout Screen Layout Example: When using LayoutDisplay each time you press Layout Layout Remote sites All Sites Site Site Site This Site Adjusting the Volume Muting the Microphone Reducing Microphone Noise 1Press Tone Adjusting the ToneConnecting the Computer Displaying a Computer’s ScreenRefresh Rate Hz ResolutionDisplaying the Computer’s Screen To return to the Home screen, press Camera Main Connecting the Sub Video Camera Displaying the Sub Video Camera’s Image1Press Camera Sub Displaying the Sub Video Camera’s ImageDocument Version Displaying Other Video SourcesOperating Manual 4Press Camera Main 14 231Press Camera Sub not normally operating Displaying the Connection Status1Press Status Example: The Boundary Microphone connection isDisplaying Unit Information Registering a New Contact Adding Contacts to the Contact List1.Use to select Site 1, Site 2 or Site Editing Contact InformationDeleting a Contact Multi-Point:Use to select 2 sites or 3 sitesRegistering a Contact from the Call History Setting the Unit Name Changing System Settings3.Use to select Network Settings and press Enter Setting the Date and TimeMaking Network Settings Making Sound SettingsMaking Connection Settings –ON: Encryption is enabled Setting the Mic Position automatically Setting the Mic PositionDisplay Unit Information Setting the Mic Position manually Mic 1: Right side Mic 2: Center Mono When setting Boundary Microphones as followsMic 1: Center stereo Mic 2: Center stereo Mic 3: Center stereoMaking Remote Control Settings Performing Self Diagnosis Performing a Network Test4.Use to select Remote access and press Enter Performing Remote MaintenanceMaking Administrator Menu Settings Logging in to the Administrator MenuMaking Language Settings Making Software Update Settings Making Encryption Settings3.When Automatic Version Check is set to ON Page Updating Software2.Use to select Update Settings and press Enter 2.Use to select Software update and press EnterThe message displayed before the second restart Making Screen Standby SettingsThe message displayed before the first restart 3.Use to select Standby Setting and press Enter Making Administrator Password SettingsPerforming System Initialization Registering a Local Site Making Local Site SettingsEditing Local Site Information Selecting a Local SiteDeleting Local Site Information Input Inputting Letters and NumbersTable 1 English Table 2 French Table 3 Spanish Document Version Switching the Input ModeDeleting an Input Character Inserting CharactersMiscellaneous Changing the Remote Control Batteries1.Open the cover 2.Take out the AA batteries Cleaning the Unit Basic Operation TroubleshootingThe remote control is unresponsive The image is distorted •Default MIC Mute set is set to ON AudioProblem Cause and SolutionSystem Settings Message If These Messages AppearCause and Solution Sub-Camerais not connected Check the connection Check sub camera setting <Check camera> Received remote control ID Miscellaneous System Specifications Index Product service When you ship the product