Manuals / Panasonic / Home Audio / Stereo Receiver

Panasonic KX-VC500 manual Check sub camera setting <Check camera>

Models: KX-VC500

1 98

Download 98 pages 49.26 Kb

Page 93

Check sub camera setting <Check camera>

Additional Information

Message

Check sub camera setting <Check camera>

Set the sub camera HDMI output to 1080i.

<Safe mode>

If [#] is pressed, the system enters safe mode after restart.

Check sub camera setting <Check camera>

Set sub camera operating frequency to nHz.

<Safe mode>

If [#] is pressed, the system enters safe mode after restart.

Note

•The field frequency setting of the KX-VC500 (50 or 60) is represented by n.

Call failed due to software version mismatch.

Call Failed due to combination mismatch.

Call Failed due to unsupported product or other error.

Cause and Solution

•A standard definition (640 × 480p, 720 × 480p) video camera signal has been detected.

→Change the video camera’s resolution to HD (1920 × 1080i).

Note

•If you enter Safe Mode during a video conference call, the call will be disconnected.

•A video camera with a different field frequency to the KX-VC500 has been detected.

→Use a video camera with the same field frequency as the KX-VC500.

Note

•If you enter Safe Mode during a video conference call, the call will be disconnected.

•A video conference call to an incompatible device was attempted.

→ Check the other party’s device. Video conference calls cannot be made to devices other than a Panasonic KX-VC500.

•A video conference call to a KX-VC500 with an incompatible software version was attempted.

→Check the software version of all parties. Update the KX-VC500 with the older software version so that the versions match.

•In a multiple-party video conference call, one or more of the parties is incompatible.

→Check the software version of all parties. Update the KX-VC500 with the older software version so that the versions match.

•An unsupported feature was used.

→Check the software version of all parties. Update the KX-VC500 with the older software version so that the versions match.

For details about supported versions and features, contact your dealer.

Document Version 2010-10

Operating Manual

93

Image 93

Panasonic KX-VC500 manual Check sub camera setting <Check camera>

Contents

Operating Manual HD Visual Communication UnitModel No. KX-VC500 Introduction Feature HighlightsOpen Source Software TrademarksSelectable Video Source Encrypted CommunicationNotice for users in California Precautioncontains perchlorate material—specialhandling may applyFor Your Safety Table of ContentsAdjusting the Volume and Tone Before OperationSpecifications Contacts and SettingsInput MiscellaneousFor Your Safety Power and Ground ConnectionGeneral Operating Safeguards Battery InstallationInstallation PowerBattery Operating ManualAbout the Operating Environment Notes about OperationAbout Moving the Device OtherPrivacy and Right of Publicity Data SecurityPreventing Data Loss Preventing Data DisclosureFCC Caution Federal Communications Commission RequirementsPart Names and Usage Main Unit FrontABC D EF G H Main Unit Back Remote Control Boundary Microphone Optional Accessory Federal Communications Commission RequirementsFor Canada Users Screen Standby LED PatternsLED pattern StatusPreparation Document VersionOperating Manual Connecting the KX-VC500 System Layout Examples Display and Main Video CameraMicrophones 40 dBsplA Noise level Micro– phone45 dBsplA 50 dBsplAAmplifier/Active Speaker Connection Connecting the Display with a Component CableTurning the Power On/Off Home Screen Idle Screen Screen DisplayMain Video Camera Image Menu Screen Idle ScreenUnit Information GuideOther party’s information Video Conference Call ScreenNetwork Status Indication Video Image1 Press Home Making a Video Conference CallThe Home screen is displayed 2Press One-TouchConnection 1 to4When you want to end the call, press End 2Select Contact List using and press Enter 1 45 2, 3 4Press Start to start the call 5When you want to end the call, press EndThe Home screen is displayed Starting a Video ConferenceCalling by Entering an IP Address 1 45 3Example: When using Input screen G: The screen will be switched to Input screen Calling from the Call History Outgoing Call HistoryIncoming Call History 1 45 2, Answering a Video Conference Call When Manual Answer is SetThe video conference begins Starting a Video Conference When Automatic Answer is SetOperating Manual Document Version1Press Layout –B Other Site: Layout –R Both Sites: Layout–G This Site: Layout each time you press Layout Example: When using Layout DisplayScreen Layout each time you press Layout Layout Remote sites All Sites Site Site Site This Site Adjusting the Volume Muting the Microphone Reducing Microphone Noise 1Press Tone Adjusting the ToneConnecting the Computer Displaying a Computer’s ScreenResolution Displaying the Computer’s ScreenRefresh Rate Hz To return to the Home screen, press Camera Main Connecting the Sub Video Camera Displaying the Sub Video Camera’s Image1Press Camera Sub Displaying the Sub Video Camera’s ImageDisplaying Other Video Sources Operating ManualDocument Version 14 23 1Press Camera Sub4Press Camera Main 1Press Status Displaying the Connection StatusExample: The Boundary Microphone connection is not normally operatingDisplaying Unit Information Registering a New Contact Adding Contacts to the Contact ListDeleting a Contact Editing Contact InformationMulti-Point:Use to select 2 sites or 3 sites 1.Use to select Site 1, Site 2 or SiteRegistering a Contact from the Call History Setting the Unit Name Changing System SettingsMaking Network Settings Setting the Date and TimeMaking Sound Settings 3.Use to select Network Settings and press EnterMaking Connection Settings –ON: Encryption is enabled Setting the Mic Position Display Unit InformationSetting the Mic Position automatically Setting the Mic Position manually Mic 1: Center stereo Mic 2: Center stereo When setting Boundary Microphones as followsMic 3: Center stereo Mic 1: Right side Mic 2: Center MonoMaking Remote Control Settings Performing Self Diagnosis Performing a Network Test4.Use to select Remote access and press Enter Performing Remote MaintenanceLogging in to the Administrator Menu Making Language SettingsMaking Administrator Menu Settings Making Software Update Settings Making Encryption Settings2.Use to select Update Settings and press Enter Updating Software2.Use to select Software update and press Enter 3.When Automatic Version Check is set to ON PageMaking Screen Standby Settings The message displayed before the first restartThe message displayed before the second restart Making Administrator Password Settings Performing System Initialization3.Use to select Standby Setting and press Enter Registering a Local Site Making Local Site SettingsEditing Local Site Information Selecting a Local SiteDeleting Local Site Information Input Inputting Letters and NumbersTable 1 English Table 2 French Table 3 Spanish Deleting an Input Character Switching the Input ModeInserting Characters Document VersionChanging the Remote Control Batteries 1.Open the cover 2.Take out the AA batteriesMiscellaneous Cleaning the Unit Basic Operation TroubleshootingThe remote control is unresponsive The image is distorted Problem AudioCause and Solution •Default MIC Mute set is set to ONSystem Settings If These Messages Appear Cause and SolutionMessage Sub-Camerais not connected Check the connection Check sub camera setting <Check camera> Received remote control ID Miscellaneous System Specifications Index Product service When you ship the product