Snmp Management Capabilities, Network | Paradyne Hotwire 7984

About the Hotwire 7984 Standalone Termination Unit

SNMP Management Capabilities

The termination unit supports SNMP Version 1, and can be managed by any industry-standard SNMP manager and accessed using SNMP by external SNMP managers.

Management Information Base (MIB) Support

For a detailed description of supported MIBs, visit Paradyne's web site at

http://www.paradyne.com. The following MIBs are supported:

HMIB II (RFC 1213 and RFC 1573) ± Defines the general objects for use with a network management protocol in TCP/IP internets and provides general information about the unit. MIB II is backward-compatible with MIB I.

HDS1 MIB (RFC 1406) ± Reports the performance status of the DSX-1 interface and supports the features found on the DSX-1 Performance Statistics screen.

HRS-232-Like MIB (RFC 1659) ± Defines objects for managing RS-232-type interfaces (e.g., V.35, RS-422, RS-423, etc.) and supports the synchronous data port on the DSU.

HEnterprise MIB ± Supports configuration, status, statistics, and tests.

SNMP Trap Support

The 7984 Standalone Termination Unit supports traps as defined in RFC 1215.

Figure 1-4 illustrates a typical M/HDSL SNMP configuration. Refer to Chapter 8,

IP Addressing and Appendix B, Standards Compliance for SNMP Traps.

Operation, Maintenance

and Provisioning Center

Network

Router

DSX-1

7984

DSL

EOC

8784

AC

T5A

250V

AC	.
INPUT	. ..

8600 Ethernet

DSLAM Interface

Ethernet

LAN

SNMP NMS

Data

99-16114a-01

Figure 1-4. HDSL SNMP Configuration

7984-A2-GB20-10

February 1999

1-5

Image 15

Paradyne Hotwire 7984 Snmp Management Capabilities, Management Information Base MIB Support, Snmp Trap Support, Network

Contents

HOTWIRE Hdsl Standalone Termination Unit Copyright E 1999 Paradyne Corporation All rights reserved Important Safety Instructions EMI Warnings Contents Initial Startup and Configuration Messages and Troubleshooting Standards Compliance for Snmp Traps About This Guide Document Purpose and Intended AudienceDocument Summary Product-Related Documents About the Hotwire Standalone Termination Unit Hotwire 7984 Termination Unit FeaturesHdsl Overview About the Hotwire 7984 Standalone Termination Unit CO Site Network Configuration Rear Panel Interface Connections Front Panel LED Status Indicators Network Snmp Management CapabilitiesManagement Information Base MIB Support Snmp Trap Support About the Hotwire 7984 Standalone Termination Unit Using the Asynchronous Terminal Interface User Interface AccessCommunication Port Settings Initiating an ATI Session Login Function SelectScreen Area Main Status Test Field Value Choices Messages Screen Work AreasInput Keys Navigating the Screens Keyboard KeysPress For the screen function Select Press Enter to Screen Function Keys Example Switching Between Screen Work Areas Ending an ATI Session Using the Asynchronous Terminal Interface Overview Initial Startup and Configuration +24 Vdc Power Supply Pinouts Connecting Power to the Unit Connecting to a System Terminal Connecting to the Network Entering Identity Information Main Menu → Control → ChangeIdentity Procedure Choosing a Configuration Mode Configuring the Unit Using the Configuration MenusConfiguration Option Area Configuration Option Set Handling Precautions for STATIC-SENSITIVE Devices Configuring the Unit Using the Internal Switches Switchpack S1 & S2 Switchpack Locations OFF = Internal Clock Switchpack DefinitionsSwitchpack S1 Definitions Switch # Allows you to OFF = Switchpacks Disabled Switchpack S2 Definitions Switch # Allows you to If you select Then Accessing and Displaying Configuration OptionsMain Menu → Configuration Load Configuration From Load Configuration from Select To Access To Configure Configuration Edit/DisplayMain Menu → Configuration → Current Configuration Main Menu → Configuration → Default Factory Main Menu → Configuration → Configuration Loader Configuration Loader Completed successfully Save Configuration Saving Configuration Options DSL Download CodeMain Menu → Control → Download Code Download Code What to Monitor Monitoring the Unit Viewing System and Test Status Main Menu → Status → System and Test StatusSystem and Test Status Health and Status SELF-TEST Results Health and Status Yyyyyyyy Self-Test Results Call your service Test Status Messages Meaning Test Status Viewing Network Error Statistics Main Menu → Status → Performance → Network Error StatisticsNetwork Error Statistics This Field Contains Viewing Network Performance Statistics This Field Contains DSX-1 Performance Statistics Viewing DSX-1 Performance Statistics This Field Contains Viewing 7984 Standalone Termination Unit LEDs Main Menu → Status → Display LEDsGeneral Standalone Termination Unit LEDs TypeLED is Indicating Monitoring the Unit Test TestingAccessing the Test Menu Main Menu → Running Network Tests Main Menu → Test → Network & DSX TestsNetwork & DSX Tests Line Loopback Repeater Loopback T1 to T1 Repeater LoopbackT1 to V.35 Repeater Loopback DTE Loopback Send Remote Line Loopback Send and Monitor Device Tests Device TestsLamp Test Main Menu → Test → Device Tests Ending an Active Test Telco-Initiated TestsTelco-Initiated Line Loopback Telco-Initiated Remote Line Loopback Telco-Initiated Payload Loopback Messages and Troubleshooting Snmp Traps Options Configuring Snmp Traps Device Messages 1 What Message Indicates What To Do Device Messages Device Messages 2 What Message Indicates What To Do Troubleshooting 1 Symptom Possible Cause Solutions Troubleshooting Troubleshooting 2 Symptom Possible Cause Solutions ATI Access Levels SecurityTables Creating a Login Administer LoginsLogin Entry On the Login Entry screen, for Enter Deleting a Login Controlling Snmp AccessAssigning Snmp Community Names and Access Types Main Menu → Configuration → Management → Security Menu Resetting the Termination Units COM Port or Factory Defaults If entering yes to prompt Then Selecting an IP Addressing Scheme IP Addressing Peer IP Address Assignments IP Addressing Example Configuration Options in , Initial Startup and Configuration Configuration Option Tables Main Menu → Configuration → Current Configuration → Network Interface Options MenuTable A-1. Network Interface Options 1 DSL Line Rate Possible Settings 400, 528, 784, 1040 Table A-1. Network Interface Options 2Circuit Identifier Port Status Main Menu → Configuration → Load Configuration From →DSX-1 Interface Options Table A-2. DSX-1 Interface Options 1 Table A-2. DSX-1 Interface Options 2 Table A-3. System Options 1 DSL ModeTest Timeout System Options Menu Table A-3. System Options 2 Telco Initiated LoopbackRemote Telco Loopback Port Use Port Type Possible Settings Asynchronous, SynchronousCommunication Port Table A-4. Communication Port Options 1 Table A-4. Communication Port Options 2 Table A-4. Communication Port Options 3 Login Required Terminal Use OnlyPort Access Level Terminal Use Only Inactivity Timeout Terminal Use Only Management and Communication Options Menu Telnet Session OptionsTelnet Session Options Table A-5. Telnet Session Options Communication Protocol Options Communication Protocol OptionsPPP Table A-6. Communication Protocol Options 1 Node IP Address Possible Settings 000.000.000.000 ±Node Subnet Mask Possible Settings 000.000.000.000 ± Default Network Destination Communication Port Link Protocol Table A-6. Communication Protocol Options 2 Snmp Management Community Name Possible Settings Ascii text field, PublicGeneral Snmp Management Options Table A-7. General Snmp Management Options 1 Name 1 Access Name 2 AccessTable A-7. General Snmp Management Options 2 Number of Managers Snmp NMS Security OptionsTable A-8. Snmp NMS Security Options 1 NMS IP Validation Table A-8. Snmp NMS Security Options 2 Access Level Number of Trap Managers Snmp Traps OptionsTable A-9. Snmp Traps Options 1 Snmp Traps Table A-9. Snmp Traps Options 2 NMS n DestinationEnterprise Specific Traps Link Traps Possible Settings Disable, Up, Down, Both Table A-9. Snmp Traps Options 3Link Trap Interfaces WarmStart AuthenticationFailureStandards Compliance for Snmp Traps Snmp Traps LinkUp/Down Variable-Bindings LinkUp and linkDown Enterprise-Specific Traps DSX Cables and Pin Assignments Position Modular Plug Unkeyed DB15 Socket T1 Network Interface Table C-2. DSL Network Interface Connector Signal Pin NumberDSL Network Interface Cable COM Port Interface Cable Figure C-3. COM Port-to-PC Cable Feature Number 7900-F1-507 Table C-3. COM Port Connector J6 Signal Direction Pin Number Power Input Connector Optional Power CableTable C-4. DC Power Connector Signal Pin Number Specifications Criteria Technical Specifications Technical Specifications COM port Glossary511 Bridged tap 703 Factory defaultsEthernet Frame relay Router ResetIP address Loopback Telnet SES IN-1 Index IN-2 IN-3 IN-4