Health and Status | Paradyne Hotwire 7984 manual

Monitoring the Unit

Health and Status

The following messages can appear in the first column of the System and Test Status screen. The highest priority Health and Status message also appears on all ATI screens on the bottom right.

Table 4-1. Health and Status Messages (1 of 2)

Message

What Message Indicates

What To Do

System Operational	There are no problems
	detected.

LOS at Net, Pt 1	An LOS (Loss Of Signal)	1.	Verify that the network cable is
	condition has been		securely attached at both ends.
	detected on the network	2.	Verify proper NTU and LTU
	interface. No signal is	2.	Verify proper NTU and LTU
	interface. No signal is		configuration
	being received on Port 1,		configuration
	being received on Port 1,
	possibly due to a local	3.	Contact network provider.
	network problem.

OOF at Net, Pt 1	An OOF (Out Of Frame)	Contact network provider.
	condition has been
	detected at the network
	interface.

LOS at DSX-1, Pt 1	An LOS (Loss Of Signal)	1.	Verify proper framing.
	condition has been	2.	Contact network provider.
	detected on the DSX-1	2.	Contact network provider.
	detected on the DSX-1
	interface.

NTU/LTU Mis match,	The NTU is not configured	Configure units to match.
Pt 1	the same as the LTU.

LOF at DSX-1, Pt 1	An LOF (Loss Of Frame)	1.	Verify that the network cable is
	condition has been		securely attached at both ends.
	detected on the DSX-1	2.	Contact network provider.
	interface.	2.	Contact network provider.
	interface.

AIS at DSX-1, Pt 1

An Alarm Indication Signal (AIS) is being received by the DSX-1 interface.

1.Verify that the units line framing and line coding are compatible.

2.Contact network provider.

EER at Net, Pt 1

An EER (Excessive Error Rate) condition has been detected on the network interface at Port 1. The condition is cleared when the error rate falls below the threshold value currently configured.

1.Ignore condition if 511 test active.

2.Contact network provider.

EER at DSX-1, Pt 1

An EER (Excessive Error Rate) condition has been detected on the DSX-1 interface.

1.Verify the attached equipment coding is compatible.

2.Contact network provider.

Yellow alarm at	A Yellow Alarm Indication	1.	Verify that the units line framing
DSX-1, Pt 1	signal is being received by		and line coding are compatible.
	the DSX-1 interface.	2.	Contact network provider.
		2.	Contact network provider.

7984-A2-GB20-10

February 1999

4-3

Image 45

Paradyne Hotwire 7984 manual Health and Status

Contents

HOTWIRE Hdsl Standalone Termination Unit Copyright E 1999 Paradyne Corporation All rights reserved Important Safety Instructions EMI Warnings Contents Initial Startup and Configuration Messages and Troubleshooting Standards Compliance for Snmp Traps About This Guide Document Purpose and Intended AudienceDocument Summary Product-Related Documents About the Hotwire Standalone Termination Unit Hotwire 7984 Termination Unit FeaturesHdsl Overview About the Hotwire 7984 Standalone Termination Unit CO Site Network Configuration Rear Panel Interface Connections Front Panel LED Status Indicators Management Information Base MIB Support Snmp Management CapabilitiesSnmp Trap Support Network About the Hotwire 7984 Standalone Termination Unit Using the Asynchronous Terminal Interface User Interface AccessCommunication Port Settings Initiating an ATI Session Login Screen SelectArea Function Main Status Test Input Screen Work AreasKeys Field Value Choices Messages Navigating the Screens Keyboard KeysPress For the screen function Select Press Enter to Screen Function Keys Example Switching Between Screen Work Areas Ending an ATI Session Using the Asynchronous Terminal Interface Overview Initial Startup and Configuration +24 Vdc Power Supply Pinouts Connecting Power to the Unit Connecting to a System Terminal Connecting to the Network Entering Identity Information Main Menu → Control → ChangeIdentity Procedure Choosing a Configuration Mode Configuring the Unit Using the Configuration MenusConfiguration Option Area Configuration Option Set Handling Precautions for STATIC-SENSITIVE Devices Configuring the Unit Using the Internal Switches Switchpack S1 & S2 Switchpack Locations Switchpack S1 Definitions Switch # Allows you to Switchpack DefinitionsOFF = Switchpacks Disabled OFF = Internal Clock Switchpack S2 Definitions Switch # Allows you to Main Menu → Configuration Load Configuration From Accessing and Displaying Configuration OptionsLoad Configuration from If you select Then Main Menu → Configuration → Current Configuration Configuration Edit/DisplayMain Menu → Configuration → Default Factory Select To Access To Configure Main Menu → Configuration → Configuration Loader Configuration Loader Completed successfully Save Configuration Saving Configuration Options Main Menu → Control → Download Code Download CodeDownload Code DSL What to Monitor Monitoring the Unit Viewing System and Test Status Main Menu → Status → System and Test StatusSystem and Test Status Health and Status SELF-TEST Results Health and Status Yyyyyyyy Self-Test Results Call your service Test Status Messages Meaning Test Status Viewing Network Error Statistics Main Menu → Status → Performance → Network Error StatisticsNetwork Error Statistics This Field Contains Viewing Network Performance Statistics This Field Contains DSX-1 Performance Statistics Viewing DSX-1 Performance Statistics This Field Contains Viewing 7984 Standalone Termination Unit LEDs Main Menu → Status → Display LEDsGeneral Standalone Termination Unit LEDs TypeLED is Indicating Monitoring the Unit Accessing the Test Menu TestingMain Menu → Test Running Network Tests Main Menu → Test → Network & DSX TestsNetwork & DSX Tests Line Loopback Repeater Loopback T1 to T1 Repeater LoopbackT1 to V.35 Repeater Loopback DTE Loopback Send Remote Line Loopback Send and Monitor Lamp Test Device TestsMain Menu → Test → Device Tests Device Tests Ending an Active Test Telco-Initiated TestsTelco-Initiated Line Loopback Telco-Initiated Remote Line Loopback Telco-Initiated Payload Loopback Messages and Troubleshooting Snmp Traps Options Configuring Snmp Traps Device Messages 1 What Message Indicates What To Do Device Messages Device Messages 2 What Message Indicates What To Do Troubleshooting 1 Symptom Possible Cause Solutions Troubleshooting Troubleshooting 2 Symptom Possible Cause Solutions ATI Access Levels SecurityTables Creating a Login Administer LoginsLogin Entry On the Login Entry screen, for Enter Deleting a Login Controlling Snmp AccessAssigning Snmp Community Names and Access Types Main Menu → Configuration → Management → Security Menu Resetting the Termination Units COM Port or Factory Defaults If entering yes to prompt Then Selecting an IP Addressing Scheme IP Addressing Peer IP Address Assignments IP Addressing Example Configuration Options in , Initial Startup and Configuration Configuration Option Tables Main Menu → Configuration → Current Configuration → Network Interface Options MenuTable A-1. Network Interface Options 1 DSL Line Rate Possible Settings 400, 528, 784, 1040 Table A-1. Network Interface Options 2Circuit Identifier DSX-1 Interface Options Main Menu → Configuration → Load Configuration From →Table A-2. DSX-1 Interface Options 1 Port Status Table A-2. DSX-1 Interface Options 2 Test Timeout DSL ModeSystem Options Menu Table A-3. System Options 1 Table A-3. System Options 2 Telco Initiated LoopbackRemote Telco Loopback Communication Port Port Type Possible Settings Asynchronous, SynchronousTable A-4. Communication Port Options 1 Port Use Table A-4. Communication Port Options 2 Port Access Level Terminal Use Only Login Required Terminal Use OnlyInactivity Timeout Terminal Use Only Table A-4. Communication Port Options 3 Management and Communication Options Menu Telnet Session OptionsTelnet Session Options Table A-5. Telnet Session Options Communication Protocol Options Communication Protocol OptionsPPP Node Subnet Mask Possible Settings 000.000.000.000 ± Node IP Address Possible Settings 000.000.000.000 ±Default Network Destination Table A-6. Communication Protocol Options 1 Communication Port Link Protocol Table A-6. Communication Protocol Options 2 General Snmp Management Options Community Name Possible Settings Ascii text field, PublicTable A-7. General Snmp Management Options 1 Snmp Management Name 1 Access Name 2 AccessTable A-7. General Snmp Management Options 2 Table A-8. Snmp NMS Security Options 1 Snmp NMS Security OptionsNMS IP Validation Number of Managers Table A-8. Snmp NMS Security Options 2 Access Level Table A-9. Snmp Traps Options 1 Snmp Traps OptionsSnmp Traps Number of Trap Managers Table A-9. Snmp Traps Options 2 NMS n DestinationEnterprise Specific Traps Link Traps Possible Settings Disable, Up, Down, Both Table A-9. Snmp Traps Options 3Link Trap Interfaces Standards Compliance for Snmp Traps AuthenticationFailureSnmp Traps WarmStart LinkUp/Down Variable-Bindings LinkUp and linkDown Enterprise-Specific Traps DSX Cables and Pin Assignments Position Modular Plug Unkeyed DB15 Socket T1 Network Interface Table C-2. DSL Network Interface Connector Signal Pin NumberDSL Network Interface Cable COM Port Interface Cable Figure C-3. COM Port-to-PC Cable Feature Number 7900-F1-507 Table C-3. COM Port Connector J6 Signal Direction Pin Number Power Input Connector Optional Power CableTable C-4. DC Power Connector Signal Pin Number Specifications Criteria Technical Specifications Technical Specifications 511 GlossaryBridged tap COM port Ethernet Factory defaultsFrame relay 703 IP address ResetLoopback Router Telnet SES IN-1 Index IN-2 IN-3 IN-4