Deleting a Login, Controlling Snmp Access | Paradyne Hotwire 7984

Security

Deleting a Login

"Procedure

1.To delete a login record, follow this menu selection sequence: Main Menu → Control → Administer Logins

2.Select PgUp or PgDn and press Enter to page through login pages/records until you find the one to be deleted.

3.Once the correct record is displayed, select Del ete and press Enter.

4.To complete the delete action, select Save and press Enter.

When the deletion is complete, Command Complete appears at the bottom of the screen. The number of login pages/records reflects one less record, and the record following the deleted record appears.

Controlling SNMP Access

There are three methods for limiting SNMP access.

HDisable the SNMP management option. Refer to Table A-8,General SNMP Management Options.

HAssign SNMP community names and access types.

HLimit SNMP access through validation of the IP address of each allowed SNMP manager.

Assigning SNMP Community Names and Access Types

The unit can be managed by an SNMP manager supporting SNMP. The community name must be supplied by an external SNMP manager accessing an object in the MIB.

To define SNMP community names, follow this menu selection sequence:

Main Menu → Configuration → Load Configuration From → Edit →

SNMP → General SNMP Management

Refer to Table A-8,General SNMP Management Options , to:

HEnable SNMP Management.

HAssign the SNMP community names of the SNMP Managers that are allowed to access the units Management Information Base (MIB).

HSpecify Read or Read/Write access for each SNMP community name.

7-4

February 1999

7984-A2-GB20-10

Image 76

Paradyne Hotwire 7984 manual Deleting a Login, Controlling Snmp Access, Assigning Snmp Community Names and Access Types

Contents

HOTWIRE Hdsl Standalone Termination Unit Copyright E 1999 Paradyne Corporation All rights reserved Important Safety Instructions EMI Warnings Contents Initial Startup and Configuration Messages and Troubleshooting Standards Compliance for Snmp Traps Document Purpose and Intended Audience About This GuideDocument Summary Product-Related Documents Hotwire 7984 Termination Unit Features About the Hotwire Standalone Termination UnitHdsl Overview About the Hotwire 7984 Standalone Termination Unit Network Configuration CO Site Front Panel LED Status Indicators Rear Panel Interface Connections Snmp Management Capabilities Management Information Base MIB SupportSnmp Trap Support Network About the Hotwire 7984 Standalone Termination Unit User Interface Access Using the Asynchronous Terminal InterfaceCommunication Port Settings Login Initiating an ATI Session Select ScreenArea Function Main Status Test Screen Work Areas InputKeys Field Value Choices Messages Keyboard Keys Navigating the ScreensPress Screen Function Keys For the screen function Select Press Enter to Switching Between Screen Work Areas Example Ending an ATI Session Using the Asynchronous Terminal Interface Initial Startup and Configuration Overview Connecting Power to the Unit +24 Vdc Power Supply Pinouts Connecting to the Network Connecting to a System Terminal Main Menu → Control → Change Entering Identity InformationIdentity Procedure Configuring the Unit Using the Configuration Menus Choosing a Configuration ModeConfiguration Option Area Configuration Option Set Configuring the Unit Using the Internal Switches Handling Precautions for STATIC-SENSITIVE Devices Switchpack Locations Switchpack S1 & S2 Switchpack Definitions Switchpack S1 Definitions Switch # Allows you toOFF = Switchpacks Disabled OFF = Internal Clock Switchpack S2 Definitions Switch # Allows you to Accessing and Displaying Configuration Options Main Menu → Configuration Load Configuration FromLoad Configuration from If you select Then Configuration Edit/Display Main Menu → Configuration → Current ConfigurationMain Menu → Configuration → Default Factory Select To Access To Configure Configuration Loader Main Menu → Configuration → Configuration Loader Completed successfully Saving Configuration Options Save Configuration Download Code Main Menu → Control → Download CodeDownload Code DSL Monitoring the Unit What to Monitor Main Menu → Status → System and Test Status Viewing System and Test StatusSystem and Test Status Health and Status SELF-TEST Results Health and Status Yyyyyyyy Call your service Self-Test Results Test Status Test Status Messages Meaning Main Menu → Status → Performance → Network Error Statistics Viewing Network Error StatisticsNetwork Error Statistics Viewing Network Performance Statistics This Field Contains This Field Contains Viewing DSX-1 Performance Statistics DSX-1 Performance Statistics This Field Contains Main Menu → Status → Display LEDs Viewing 7984 Standalone Termination Unit LEDsGeneral Type Standalone Termination Unit LEDsLED is Indicating Monitoring the Unit Testing Accessing the Test MenuMain Menu → Test Main Menu → Test → Network & DSX Tests Running Network TestsNetwork & DSX Tests Line Loopback T1 to T1 Repeater Loopback Repeater LoopbackT1 to V.35 Repeater Loopback DTE Loopback Send Remote Line Loopback Send and Monitor Device Tests Lamp TestMain Menu → Test → Device Tests Device Tests Telco-Initiated Tests Ending an Active TestTelco-Initiated Line Loopback Telco-Initiated Payload Loopback Telco-Initiated Remote Line Loopback Messages and Troubleshooting Configuring Snmp Traps Snmp Traps Options Device Messages Device Messages 1 What Message Indicates What To Do Device Messages 2 What Message Indicates What To Do Troubleshooting Troubleshooting 1 Symptom Possible Cause Solutions Troubleshooting 2 Symptom Possible Cause Solutions Security ATI Access LevelsTables Administer Logins Creating a LoginLogin Entry On the Login Entry screen, for Enter Controlling Snmp Access Deleting a LoginAssigning Snmp Community Names and Access Types Resetting the Termination Units COM Port or Factory Defaults Main Menu → Configuration → Management → Security Menu If entering yes to prompt Then IP Addressing Selecting an IP Addressing Scheme IP Addressing Example Peer IP Address Assignments Configuration Option Tables Configuration Options in , Initial Startup and Configuration Network Interface Options Menu Main Menu → Configuration → Current Configuration →Table A-1. Network Interface Options 1 Table A-1. Network Interface Options 2 DSL Line Rate Possible Settings 400, 528, 784, 1040Circuit Identifier Main Menu → Configuration → Load Configuration From → DSX-1 Interface OptionsTable A-2. DSX-1 Interface Options 1 Port Status Table A-2. DSX-1 Interface Options 2 DSL Mode Test TimeoutSystem Options Menu Table A-3. System Options 1 Telco Initiated Loopback Table A-3. System Options 2Remote Telco Loopback Port Type Possible Settings Asynchronous, Synchronous Communication PortTable A-4. Communication Port Options 1 Port Use Table A-4. Communication Port Options 2 Login Required Terminal Use Only Port Access Level Terminal Use OnlyInactivity Timeout Terminal Use Only Table A-4. Communication Port Options 3 Telnet Session Options Management and Communication Options MenuTelnet Session Options Table A-5. Telnet Session Options Communication Protocol Options Communication Protocol OptionsPPP Node IP Address Possible Settings 000.000.000.000 ± Node Subnet Mask Possible Settings 000.000.000.000 ±Default Network Destination Table A-6. Communication Protocol Options 1 Table A-6. Communication Protocol Options 2 Communication Port Link Protocol Community Name Possible Settings Ascii text field, Public General Snmp Management OptionsTable A-7. General Snmp Management Options 1 Snmp Management Name 2 Access Name 1 AccessTable A-7. General Snmp Management Options 2 Snmp NMS Security Options Table A-8. Snmp NMS Security Options 1NMS IP Validation Number of Managers Access Level Table A-8. Snmp NMS Security Options 2 Snmp Traps Options Table A-9. Snmp Traps Options 1Snmp Traps Number of Trap Managers NMS n Destination Table A-9. Snmp Traps Options 2Enterprise Specific Traps Table A-9. Snmp Traps Options 3 Link Traps Possible Settings Disable, Up, Down, BothLink Trap Interfaces AuthenticationFailure Standards Compliance for Snmp TrapsSnmp Traps WarmStart LinkUp and linkDown LinkUp/Down Variable-Bindings Enterprise-Specific Traps DSX Cables and Pin Assignments T1 Network Interface Position Modular Plug Unkeyed DB15 Socket Signal Pin Number Table C-2. DSL Network Interface ConnectorDSL Network Interface Cable Figure C-3. COM Port-to-PC Cable Feature Number 7900-F1-507 COM Port Interface Cable Table C-3. COM Port Connector J6 Signal Direction Pin Number Optional Power Cable Power Input ConnectorTable C-4. DC Power Connector Signal Pin Number Technical Specifications Specifications Criteria Technical Specifications Glossary 511Bridged tap COM port Factory defaults EthernetFrame relay 703 Reset IP addressLoopback Router SES Telnet Index IN-1 IN-2 IN-3 IN-4