Manuals / Paradyne / Computer Equipment / Network Router

Paradyne Hotwire 7984 manual Connecting Power to the Unit, +24 Vdc Power Supply Pinouts, Procedure

Models: Hotwire 7984

1 122

Download 122 pages 48.4 Kb

Page 28

Initial Startup and Configuration

Connecting Power to the Unit

If your package includes a power pack: Plug the power pack into an ac outlet having a nominal voltage rating between 100±240 Vac. Connect the output cable of the power pack to the connector marked POWER on the rear panel.

If your package includes a direct-connection +24 Vdc power cable: Connect the unit to an external +24 Vdc power source as described in Connecting the Unit to an Optional External +24 Vdc Power Source.

If you will use a ±48 Vdc power supply: Connect the unit to an external ±48 Vdc power source as described in the documentation shipped with the power supply and power cable.

Connecting the Unit to an Optional External +24 Vdc Power Source

Using the dc power cable, the Hotwire 7984 Standalone Termination Unit is capable of operating on a +24 Vdc power supply.

"Procedure

To use the dc power cable:

1.Connect the green wire to a suitable ground.

2.Connect the orange wire to the +24 Vdc source.

3.Connect the white wire to the return.

4.Cut the black, red, and blue wires off at the outer insulation.

5.Plug the power connector into the 7984 Standalone Termination Unit.

		Black	X
	1

		Red
	2		X

		Green
	3		Ground

		White
	4		RTN

		Orange
	5		+24 Vdc
		Blue
	6		X

99-14158-02

+24 Vdc Power Supply Pinouts

3-2

February 1999

7984-A2-GB20-10

Image 28

Paradyne Hotwire 7984 manual Connecting Power to the Unit, Connecting the Unit to an Optional External +24 Vdc Power Source

Contents

HOTWIRE M/HDSL STANDALONE TERMINATION UNIT WITH DSX-1 INTERFACEUSERS GUIDE Document No. 7984-A2-GB20-10Warranty, Sales, and Service Information Copyright E 1999 Paradyne Corporation All rights reservedPrinted in U.S.A TrademarksImportant Safety Instructions EMI Warnings To Users of Digital Apparatus in CanadaContents 1 About the Hotwire 7984 Standalone Termination Unit2 Using the Asynchronous Terminal Interface About This GuideMonitoring the Unit Initial Startup and ConfigurationContents 5 Testing 6 Messages and Troubleshooting7 Security 8 IP AddressingA Configuration Option Tables D Technical Specifications Glossary IndexB Standards Compliance for SNMP Traps C Cables and Pin Assignments7984 Termination Units features and capabilities Using the Asynchronous Terminal Interface. Providesinstructions for accessing the user interface and navigating Initial Startup and Configuration. Provides procedures forConfiguration Option Tables. Contains all configuration options, default settings, and possible settingsCables and Pin Assignments. Contains connector and Technical Specifications. Contains physical and regulatoryHotwire 7984 Termination Unit Features About the Hotwire Standalone Termination UnitM/HDSL Overview H Local Management standalone unit. Provides local management using a Network Configuration Figure 1-1. Sample M/HDSL ConfigurationsFront Panel LED Status Indicators Figure 1-2. Hotwire 7984 Standalone Termination Unit Front PanelFigure 1-3. Hotwire 7984 Standalone Termination Unit Rear Panel Rear Panel Interface ConnectionsFigure 1-4. HDSL SNMP Configuration SNMP Management CapabilitiesManagement Information Base MIB Support SNMP Trap SupportAbout the Hotwire 7984 Standalone Termination Unit FebruaryUser Interface Access Using the Asynchronous Terminal InterfaceCommunication Port Settings Initiating an ATI Session Select Using the Asynchronous Terminal Interface Screen Work Areas Main Menu → Configuration → Load Configuration From → NetworkInterface Options Procedure Navigating the ScreensKeyboard Keys PressScreen Function Keys For the screen functionAnd press Enter to SelectExample Switching Between Screen Work AreasProcedure Ending an ATI Session ProcedureUsing the Asynchronous Terminal Interface 2-10February Initial Startup and Configuration OverviewConnecting Power to the Unit Connecting the Unit to an Optional External +24 Vdc Power Source+24 Vdc Power Supply Pinouts ProcedureConnecting to the Network Connecting to a System TerminalProcedure ProcedureEntering Identity Information Main Menu → Control → ChangeProcedure Choosing a Configuration Mode Configuring the Unit Using the Configuration MenusH Referring to Appendix A, Configuration Option Tables Configuration Option AreaHANDLING PRECAUTIONS FOR STATIC-SENSITIVE DEVICES Configuring the Unit Using the Internal SwitchesProcedure Switchpack S1 & S2 Switchpack Locations98-16073a Switchpack Definitions Table 3-1. Switchpack S1 DefinitionsSwitch # Allows you toTable 3-2. Switchpack S2 Definitions Table 3-3. DSL Line Rate, Switches 3±5 on Switchpack S2Switch Position 3-10Accessing and Displaying Configuration Options Main Menu → Configuration Load Configuration From3-11 If you selectConfiguration Edit/Display Main Menu → Configuration → Current ConfigurationMain Menu → Configuration → Default Factory To Access theConfiguration Loader Main Menu → Configuration → Configuration Loader3-13 Procedure3-14 Completed successfullySaving Configuration Options 3-15Procedure If you selectDownload Code 3-16Main Menu → Control → Download Code ProcedureMonitoring the Unit What to MonitorViewing System and Test Status Main Menu → Status → System and Test StatusHealth and Status Table 4-1. Health and Status Messages 1 ofMessage What Message IndicatesTable 4-1. Health and Status Messages 2 of MessageWhat Message Indicates What To DoSelf-Test Results Table 4-2. Self-Test Results MessagesCall your service MessageTest Status Table 4-3. Test Status MessagesTest Status Message MeaningMain Menu → Status → Performance → Network Error Statistics Viewing Network Error StatisticsH SES Severely Errored Seconds Seconds during which more than Viewing Network Performance Statistics This FieldContains Main Menu → Status → Performance → Network Performance StatisticsThis Field Contains4-10 Viewing DSX-1 Performance StatisticsMain Menu → Status → Performance → DSX-1 Performance Statistics This Field 4-11Contains 4-12 Viewing 7984 Standalone Termination Unit LEDsMain Menu → Status → Display LEDs 7984 Standalone Termination Unit LEDs 4-13Type LED isMonitoring the Unit 4-14February Testing Accessing the Test MenuMain Menu → SelectRunning Network Tests Main Menu → Test → Network & DSX TestsLine Loopback ProcedureRepeater Loopback T1 to T1 Repeater LoopbackT1 to V.35 Repeater Loopback ProcedureDTE Loopback ProcedureSend Remote Line Loopback ProcedureSend and Monitor ProcedureDevice Tests Lamp TestMain Menu → Test → Device Tests ProcedureEnding an Active Test Telco-Initiated TestsTelco-Initiated Line Loopback Activation and DeactivationTelco-Initiated Remote Line Loopback Telco-Initiated Payload Loopback5-10 H Configuring SNMP Traps H Device Messages H Troubleshooting Messages and TroubleshootingOverview Main Menu → Configuration → Load Configuration From → Configuring SNMP TrapsManagement and Communication Options → SNMP Traps Options Device Messages Table 6-1. Device Messages 1 ofDevice Message What Message IndicatesTable 6-1. Device Messages 2 of Messages and TroubleshootingDevice Message What Message IndicatesTroubleshooting Table 6-2. Troubleshooting 1 ofSymptom SolutionsTable 6-2. Troubleshooting 2 of Messages and TroubleshootingSymptom SolutionsATI Access Levels Table 7-1. Access LevelsATI Access to Menu Functions AdministratorCreating a Login ProcedureOn the Login Entry screen, for the EnterDeleting a Login Controlling SNMP AccessAssigning SNMP Community Names and Access Types Main Menu → Configuration → Load Configuration From → Edit →Resetting the Termination Units COM Port or Factory Defaults Limiting SNMP Access through the IP Addresses of the ManagersMain Menu → Configuration → Management → Security Menu ProcedureIf entering yes to prompt ThenIP Addressing Selecting an IP Addressing SchemeIP Addressing Example Peer IP Address AssignmentsConfiguration Option Tables Configuration Options in Chapter 3, Initial Startup and ConfigurationTo Access the To Configure theMain Menu → Configuration → Current Configuration → Network Interface Options MenuTable A-1. Network Interface Options 1 of Excessive Error Rate ThresholdTable A-1. Network Interface Options 2 of DSL Line Rate Possible Settings 400, 528, 784, 1040Possible Settings 000.000.000.001 ± 223.255.255.255, Clear Peer IP Address LTU OnlyDSX-1 Interface Options Table A-2. DSX-1 Interface Options 1 ofMain Menu → Configuration → Load Configuration From → Port StatusTable A-2. DSX-1 Interface Options 2 of Line Coding FormatLine Equalization Send AIS on Network FailureSystem Options Menu Table A-3. System Options 1 ofMain Menu → Configuration → Load Configuration From → Test TimeoutTelco Initiated Loopback Table A-3. System Options 2 ofRemote Telco Loopback Main Menu → Configuration → Load Configuration From → Communication Communication PortPort Table A-4. Communication Port Options 1 ofTable A-4. Communication Port Options 2 of Data Rate Possible Settings 9.6, 14.4, 19.2, 28.8Character Length Terminal Use Only Parity Terminal Use OnlyA-10 Table A-4. Communication Port Options 3 ofLogin Required Terminal Use Only Port Access Level Terminal Use OnlyManagement and Communication Options Menu Telnet Session OptionsA-11 Management and Communication → TelnetA-12 Table A-5. Telnet Session OptionsTelnet Login Required Session Access LevelCommunication Protocol Options A-13Management and Communication → Comm Protocol Options Main Menu → Configuration → Load Configuration From →A-14 Table A-6. Communication Protocol Options 1 ofNode IP Address Possible Settings 000.000.000.000 ± Node Subnet Mask Possible Settings 000.000.000.000 ±A-15 Table A-6. Communication Protocol Options 2 ofCommunication Port Subnet Mask Possible Settings 000.000.000.000 ± Communication Port Link ProtocolGeneral SNMP Management Options A-16Management and Communication → SNMP → General SNMP Management Table A-7. General SNMP Management Options 1 ofA-17 Table A-7. General SNMP Management Options 2 ofName 1 Access Community Name Possible Settings ASCII text field, PublicSNMP NMS Security Options A-18Management and Communication → SNMP → Security Table A-8. SNMP NMS Security Options 1 ofA-19 Table A-8. SNMP NMS Security Options 2 ofPossible Settings 000.000.000.000 ± 223.255.255.255, Clear Access LevelSNMP Traps Options A-20Management and Communication → SNMP Traps Table A-9. SNMP Traps Options 1 ofA-21 Table A-9. SNMP Traps Options 2 ofPossible Settings 000.000.000.000 ± 223.255.255.255, Clear General Traps Possible Settings Disable, Warm, AuthFail, BothA-22 Table A-9. SNMP Traps Options 3 ofLink Traps Possible Settings Disable, Up, Down, Both Link Trap InterfacesauthenticationFailure Standards Compliance for SNMP TrapsSNMP Traps warmStartlinkUp and linkDown linkUp/Down Variable-BindingsEnterprise-Specific Traps SNMP TrapDescription Possible CauseInterface enterpriseTestStart/StopVariable-Bindings Possible CauseH COM Port Interface Cable H Power Input Connector H Optional Power CableCables and Pin Assignments H T1 Network Interface Cable H DSL Network Interface CableTable C-1. T1 100-Ohm Balanced Interface Connector SignalT1 Network Interface Pin NumberTable C-2. DSL Network Interface Connector DSL Network Interface CableSignal Pin NumberFigure C-3. COM Port-to-PC Cable Feature Number 7900-F1-507 COM Port Interface CableTable C-3. COM Port Connector J6 DirectionSignal Pin NumberPower Input Connector Optional Power CableTable C-4. DC Power Connector DC Power Cable Feature Number 7900-F1-506Technical Specifications SpecificationsCriteria WeightTechnical Specifications Glossary GL-1bridged tap COM portfactory defaults GL-2DSLAM DTLBreset GL-3HDSL IP addressGL-4 SNMPTCP/IP TelnetIndex IN-1IN-2 IN-3 IN-4