Dsx | Paradyne Hotwire 7984 instruction

Standards Compliance for SNMP Traps

The tests that affect the enterpriseTestStart, enterpriseTestStop, and the variable-bindings are different for each particular interface. Diagnostic tests are only supported on the physical T1 network and user data port interfaces. The specific tests and variable-bindings are described in the following table:

Interface	enterpriseTestStart/Stop	Possible Cause
Interface	Variable-Bindings	Possible Cause

DSL Network	H ifIndex (RFC 1573)	H enterpriseTest Start ± Any
	H ifAdminStatus (RFC 1573)	one of the following tests is
	H ifAdminStatus (RFC 1573)	active on the interface:
		active on the interface:
	H ifOperStatus (RFC 1573)	± Line Loopback
	H ifType (RFC 1573)	± Payload Loopback
	H ifTestType (RFC 1573)	± Repeater Loopback
	H ifTestType (RFC 1573)	± Remote Line Loopback
	The following objects control tests	± Remote Line Loopback
	The following objects control tests	± Send and Monitor 511
	in SNMP-managed devices:	± Send and Monitor 511
	± noTest ± Stops the test in	H enterpriseTest Stop ± No tests
	progress.	currently running on the
	± testLoopLLB ± Initiates a Local	interface.
	Loopback.
	± testLoopPLB ± Initiates a
	Payload Loopback.
	± testLoopRLB ± Initiates a
	Remote Loopback.
	± testSendMon511 ± Initiates a
	Send and Monitor 511 test.
	± testSendLLBUp ± Initiates an
	LLB Up message to the remote
	unit.
	± testSendLLBDown ± Initiates an
	LLB Down message to the
	remote unit.

DSX	H ifIndex (RFC 1573)
	H ifAdminStatus (RFC 1573)
	H ifOperStatus (RFC 1573)
	H ifTestType (RFC 1573)
	The following objects control tests
	in SNMP-managed devices:
	± noTest ± Stops the test in
	progress.
	± testLoopExternalDTE

B-4

February 1999

7984-A2-GB20-10

Image 106

Paradyne Hotwire 7984 manual Dsx

Contents

HOTWIRE Hdsl Standalone Termination Unit Copyright E 1999 Paradyne Corporation All rights reserved Important Safety Instructions EMI Warnings Contents Initial Startup and Configuration Messages and Troubleshooting Standards Compliance for Snmp Traps Document Purpose and Intended Audience About This GuideDocument Summary Product-Related Documents Hotwire 7984 Termination Unit Features About the Hotwire Standalone Termination UnitHdsl Overview About the Hotwire 7984 Standalone Termination Unit Network Configuration CO Site Front Panel LED Status Indicators Rear Panel Interface Connections Snmp Trap Support Snmp Management CapabilitiesManagement Information Base MIB Support Network About the Hotwire 7984 Standalone Termination Unit User Interface Access Using the Asynchronous Terminal InterfaceCommunication Port Settings Login Initiating an ATI Session Area SelectScreen Function Main Status Test Keys Screen Work AreasInput Field Value Choices Messages Keyboard Keys Navigating the ScreensPress Screen Function Keys For the screen function Select Press Enter to Switching Between Screen Work Areas Example Ending an ATI Session Using the Asynchronous Terminal Interface Initial Startup and Configuration Overview Connecting Power to the Unit +24 Vdc Power Supply Pinouts Connecting to the Network Connecting to a System Terminal Main Menu → Control → Change Entering Identity InformationIdentity Procedure Configuring the Unit Using the Configuration Menus Choosing a Configuration ModeConfiguration Option Area Configuration Option Set Configuring the Unit Using the Internal Switches Handling Precautions for STATIC-SENSITIVE Devices Switchpack Locations Switchpack S1 & S2 OFF = Switchpacks Disabled Switchpack DefinitionsSwitchpack S1 Definitions Switch # Allows you to OFF = Internal Clock Switchpack S2 Definitions Switch # Allows you to Load Configuration from Accessing and Displaying Configuration OptionsMain Menu → Configuration Load Configuration From If you select Then Main Menu → Configuration → Default Factory Configuration Edit/DisplayMain Menu → Configuration → Current Configuration Select To Access To Configure Configuration Loader Main Menu → Configuration → Configuration Loader Completed successfully Saving Configuration Options Save Configuration Download Code Download CodeMain Menu → Control → Download Code DSL Monitoring the Unit What to Monitor Main Menu → Status → System and Test Status Viewing System and Test StatusSystem and Test Status Health and Status SELF-TEST Results Health and Status Yyyyyyyy Call your service Self-Test Results Test Status Test Status Messages Meaning Main Menu → Status → Performance → Network Error Statistics Viewing Network Error StatisticsNetwork Error Statistics Viewing Network Performance Statistics This Field Contains This Field Contains Viewing DSX-1 Performance Statistics DSX-1 Performance Statistics This Field Contains Main Menu → Status → Display LEDs Viewing 7984 Standalone Termination Unit LEDsGeneral Type Standalone Termination Unit LEDsLED is Indicating Monitoring the Unit Main Menu → TestingAccessing the Test Menu Test Main Menu → Test → Network & DSX Tests Running Network TestsNetwork & DSX Tests Line Loopback T1 to T1 Repeater Loopback Repeater LoopbackT1 to V.35 Repeater Loopback DTE Loopback Send Remote Line Loopback Send and Monitor Main Menu → Test → Device Tests Device TestsLamp Test Device Tests Telco-Initiated Tests Ending an Active TestTelco-Initiated Line Loopback Telco-Initiated Payload Loopback Telco-Initiated Remote Line Loopback Messages and Troubleshooting Configuring Snmp Traps Snmp Traps Options Device Messages Device Messages 1 What Message Indicates What To Do Device Messages 2 What Message Indicates What To Do Troubleshooting Troubleshooting 1 Symptom Possible Cause Solutions Troubleshooting 2 Symptom Possible Cause Solutions Security ATI Access LevelsTables Administer Logins Creating a LoginLogin Entry On the Login Entry screen, for Enter Controlling Snmp Access Deleting a LoginAssigning Snmp Community Names and Access Types Resetting the Termination Units COM Port or Factory Defaults Main Menu → Configuration → Management → Security Menu If entering yes to prompt Then IP Addressing Selecting an IP Addressing Scheme IP Addressing Example Peer IP Address Assignments Configuration Option Tables Configuration Options in , Initial Startup and Configuration Network Interface Options Menu Main Menu → Configuration → Current Configuration →Table A-1. Network Interface Options 1 Table A-1. Network Interface Options 2 DSL Line Rate Possible Settings 400, 528, 784, 1040Circuit Identifier Table A-2. DSX-1 Interface Options 1 Main Menu → Configuration → Load Configuration From →DSX-1 Interface Options Port Status Table A-2. DSX-1 Interface Options 2 System Options Menu DSL ModeTest Timeout Table A-3. System Options 1 Telco Initiated Loopback Table A-3. System Options 2Remote Telco Loopback Table A-4. Communication Port Options 1 Port Type Possible Settings Asynchronous, SynchronousCommunication Port Port Use Table A-4. Communication Port Options 2 Inactivity Timeout Terminal Use Only Login Required Terminal Use OnlyPort Access Level Terminal Use Only Table A-4. Communication Port Options 3 Telnet Session Options Management and Communication Options MenuTelnet Session Options Table A-5. Telnet Session Options Communication Protocol Options Communication Protocol OptionsPPP Default Network Destination Node IP Address Possible Settings 000.000.000.000 ±Node Subnet Mask Possible Settings 000.000.000.000 ± Table A-6. Communication Protocol Options 1 Table A-6. Communication Protocol Options 2 Communication Port Link Protocol Table A-7. General Snmp Management Options 1 Community Name Possible Settings Ascii text field, PublicGeneral Snmp Management Options Snmp Management Name 2 Access Name 1 AccessTable A-7. General Snmp Management Options 2 NMS IP Validation Snmp NMS Security OptionsTable A-8. Snmp NMS Security Options 1 Number of Managers Access Level Table A-8. Snmp NMS Security Options 2 Snmp Traps Snmp Traps OptionsTable A-9. Snmp Traps Options 1 Number of Trap Managers NMS n Destination Table A-9. Snmp Traps Options 2Enterprise Specific Traps Table A-9. Snmp Traps Options 3 Link Traps Possible Settings Disable, Up, Down, BothLink Trap Interfaces Snmp Traps AuthenticationFailureStandards Compliance for Snmp Traps WarmStart LinkUp and linkDown LinkUp/Down Variable-Bindings Enterprise-Specific Traps DSX Cables and Pin Assignments T1 Network Interface Position Modular Plug Unkeyed DB15 Socket Signal Pin Number Table C-2. DSL Network Interface ConnectorDSL Network Interface Cable Figure C-3. COM Port-to-PC Cable Feature Number 7900-F1-507 COM Port Interface Cable Table C-3. COM Port Connector J6 Signal Direction Pin Number Optional Power Cable Power Input ConnectorTable C-4. DC Power Connector Signal Pin Number Technical Specifications Specifications Criteria Technical Specifications Bridged tap Glossary511 COM port Frame relay Factory defaultsEthernet 703 Loopback ResetIP address Router SES Telnet Index IN-1 IN-2 IN-3 IN-4