Keyboard Address Switch Settings, Off | Pelco CM6800E-48X8 specs

3.Set the keyboard DIP switches for the desired address for the local keyboard (refer to Figure 12 and Table D).

Table D. Keyboard Addresses: KBD100/200A/300A Series Keyboards

Keyboard

Address

Switch Settings

1

2

3

4

1

0

OFF

OFF

OFF

OFF

2

1

ON

OFF

OFF

OFF

3

2

OFF

ON

OFF

OFF

4

3

ON

ON

OFF

OFF

5

4

OFF

OFF

ON

OFF

6

5

ON

OFF

ON

OFF

7

6

OFF

ON

ON

OFF

8

7

ON

ON

ON

OFF

Table E. Switch Settings—KBD200A/300A Keyboards Only

Keyboard

Switch

5

6

7

8

KBD200A

OFF

OFF

OFF (NOT USED)

OFF

KBD300A

OFF

ON or OFF*

OFF (NOT USED)

OFF

* Switch 6 enables/disables turbo pan (can be switched while keyboard is on).

C1528M-F (6/05)

23

Image 23

Pelco CM6800E-48X8 manual Keyboard Address Switch Settings, Off, Table E. Switch Settings-KBD200A/300A Keyboards Only

Contents

CM6800E-48X8 Contents Control Genex Multiplexer and Genex Multiplexer Displays List of Illustrations List of Tables C1528M-F 6/05 For Qualified Service Personnel only Important Safeguards and Warnings Sample CM6800E-48X8 System Description Sample CM6800E 96 x 16 System Keyboards Sequences, Macros, Presets, Patterns, and ZonesSystem Access and Priority Programming Continuous Operating Device Alarm InputsPower, Mounting Methods Auxiliary Outputs Associated Equipment ModelsCompatible Products Additional Resources Mounting Installation Main unit Cameras Expansion unit Cameras 96 x 16 System Default Camera NumbersVideo Sources Cable Type Maximum Distance Connecting Looping Video Sources 96 x 16 System PTZ Control Capacity Control Lines Main unit Monitor Expansion Unit Monitor Monitors96 x 16 System Monitor Capacity Main unit Alarms Expansion Unit Alarms Alarms96 x 16 System Alarm Capacity CM9760-MDA, Ascii Connecting Devices Through the Communication PortsInput Type Wiring Pin-Outs Default Device RS-485, 19200 baud, no parity, 8 data bits, 1 stop bit RS-485 Pin-Outs Ascii device CM9760-MDA, Satellite Rx+Ground Tx+ RS-232 Pin-Outs RJ-45 Port CM6800E Communication Port Connections and Options KBD100, KBD200A, and KBD300A Series Keyboards KBD100, KBD200A, and KBD300A Direct-Powered Keyboards OFF Keyboard Address Switch SettingsTable E. Switch Settings-KBD200A/300A Keyboards Only Keyboard Switch Remote Keyboards KBD100, KBD200A, and KBD300A Remote Keyboards KBD960/KBR960 REL2064 ALM2064 Devices KBD960, ALM2064, REL2064Devices Addressing Connecting a KBD960/KBR960 to the CM6800E Connecting a Single KBD960/KBR960 Keyboard To connect a single ALM2064 Alarm Interface Unit Connecting a Single ALM2064 Alarm Interface Unit To connect a single REL2064 Relay Interface Unit Connecting a Single REL2064 Relay Interface Unit Multiple M Devices Local Connection Multiple M Devices Multiple M Devices Remote Connection Connecting Multiple M Devices Remote Connection PC Connection to RJ-45 Port Connecting a PC Connecting Genex Multiplexers Connecting Genex Multiplexers Main unit AUX Expansion Unit AUX Connecting Relay Contacts AUX 1Local Auxiliaries 96 x 16 System Auxiliary Capacity Wiring the F3 TTL Output Connecting the Open Collector Output F3 TTL CM6800E-48X8 Main Unit Connecting a 96 X 16 System Initialize Keyboards POWER-UP the SystemSystem START-UP COM Configure the SystemPort Default Settings Communication Ports Control MUX 96 X 16 System SettingsKBD960/KBR960 Keyboard Genex Multiplexer Additional Programming Monitor Color AdjustmentProgram Presets Programming the CM6800E Select Language CM6800E Programming ModeExit Programming Mode Keyboard Entries in Programming ModeFunction Navigate to the Next or Previous field Press F1 Navigate to the Help field Press F1 Camera to Monitor AccessKeyboard to Monitor Camera to Keyboard Program Alarm Groups Alarm Programming Program AN Internal or External Alarm Contact Priority AUX field, select an auxiliary to be activatedACK Type Type Program Video Loss Alarms Program a Video Loss Alarm Assign a Logical Alarm Number Assign a Logical Alarm Number Optional Latching or Momentary Operation Alarm-based OperationMode field for each auxiliary, select either LAT or MOM Auxiliary Outputs If necessary, first program logical camera number Camera ProgrammingProgram Logical Numbers Program Cameras Select Character Program Vertical Drive Option Optional Event Timers Macro Status View Screen Macros Type Display Values Monitor DisplayMonitor Camera Title Date Monitor Status Display ValuesALM Status Display Values Time Use the Set Password screen to change the system password Password Action Ascii text Ports SERIAL/COM PortsSerial Port Input on CM6800E rear panel Level 1 = highest priority Level 8 = lowest priority PriorityPort Options Change the System Setting 96 X 16 System Settings Sequence Sequences Turn camera auxiliary on AUX and ##Turn global auxiliary on Turn global auxiliary off Options DD/MMM/YY MMM/DD/YY YY/MMM/DD DD/MM/YY YY/MM/DD PATTERNS, PRESETS, and ZonesTime and Date Operating the CM6800E Switch MonitorsOperation Overview Control Receivers To move through the sequence one camera at a time Operate Sequences Select To start the macro RUN a MacroSelect Macro to start the macro Call a Preset Acknowledge AN Alarm Patterns are not available with the KBD100 keyboard Create and RUN a Pattern Operate an Auxiliary in a Receiver Operate AUXILIARIES/RELAYSOperate a Local Auxiliary Operate an External Auxiliary Define Zones Control Genex Multiplexer and Genex Multiplexer DisplaysOperate Scanning Functions Detect Video Loss Appendix CM6800E DIP SwitchesCM6800E DIP Switch Default Setting Switch Chronological Pair D and Q Alarm Group Display OptionsMonitor Alarm Alarms Block Build Salvo Group Monitor Alarm Alarms Next Display CycleReverse Chronological Pair M and L Auxiliary Notes Macro CommandsDescription Specify Fields HEX PipoQuad Nano Install the CM6800E AS a Satellite Device Page Satellite Monitor Access Configure the CM6800E AS a Satellite Device Change the Port Setting Satellite Port Settings Enable Alarm Contacts Satellite Alarms Optional Add a Satellite Device in the CM9700-MGR Configure CM9700-MGR System Manager Settings Configure CM9760-MGR System Manager Settings Click the Comms tab. The Comms page appears Program the Comms File Click the Cameras tab. The Cameras page appears Program the Cameras File Click the Link Cameras tab. The Link Cameras page appears Program the Link Cameras File Click OK to close the Alarm Camera Switches dialog box Program the Alarms File OptionalClick the Alarms tab. The Alarms page appears Press 89 Preset How to Display the CM6800E Programming Main MenuHow to Exit Programming Mode How to Select a Numerical Value in an Option Field Link Camera page Phy Num column Logical Number Assignment Table for Link CamerasLink Camera Name 3Ma16#a Ascii Operating CommandsFunctional Procedure Commands Result Uppercase characters Desired Action Command Result Logical Alarm Number in the Alarm Programming section 48~Jva Trigger an alarm #EaClear an alarm #Ia Acknowledge an alarm #Ka Panel An alarm is triggered #Ea Wait AT Least Five Seconds TroubleshootingGaining Initial Control Dip Switch Cover Plate Software Reset Problem Remedy Solutions to Common Problems Icon/Button Legend KBD960/KBR960 ICON/BUTTON Legend Upgrade the CM6800 Switcher Software Upgrade the CM6800 Switcher Software Ascii GlossaryTerm Definition PTZ NtscPAL Recommended distance is 4,000 feet 1,219 m All four wiresStar configuration RS-422 Specifications 96 x 16 System Regulatory Notices48 x 8 System Product Warranty and Return Information C1528M-F 6/05 105 ISO9001