Pelco CM6800E-48X8 manual Connecting Genex Multiplexers

CONNECTING GENEX MULTIPLEXERS

Use COM 4 to connect up to eight Genex Multiplexers to the CM6800E.

1.Connect the COM IN port of the multiplexer to COM 4 on the CM6800E, using the 6-foot (1.8 m) reversed data cable supplied with the CM6800E.

One reversed cable and four straight cables are supplied with the CM6800E. Use the reversed cable for connecting the Genex multiplexer to the CM6800E.

A straight data cable is supplied with the Genex multiplexer. Use this cable for connecting a second Genex multiplexer to the first multiplexer, if necessary.

2.Connect the MAIN monitor output from the multiplexer to any of the 48 camera inputs on the CM6800E.

3.Connect cameras to the multiplexer and then loop them to the CM6800E. Refer to the MX4000 Genex Series Simplex and Duplex Multiplexers Installation/Operation Manual for detailed camera connection instructions. Terminate the video loop at the CM6800E.

4.If required, you can connect a total of eight Genex multiplexers through COM 4. Daisy-chain the multiplexers by connecting a straight data cable from the COM OUT port on the first multiplexer to the COM IN port on the second multiplexer; connect the COM OUT port on the second multiplexer to the COM IN port on the third multiplexer. Continue to the eighth multiplexer, if necessary.

Refer to the System Start-Upsection for additional configuration steps required when using a Genex Multiplexer.

010101

HZ								9	10	11	12	13	14	15	16
1	2	3	4	5	6	7	8
75															1	5

																2	6
17	18	19	20	21	22	23	24	25	26	27	28	29	30	31	32	3	7
								41	42	43	44	1	2	3	4	4	8
33	34	35	36	37	38	39	40	45	46	47	48	5	6	7	8

ALT

1 2 3 4 5 6 7 8

		CONTROL
A T	T	R R	T	T	R R B
+	-	- +	+	-	- +
					F
	1		2		3
1
					120/230~
					50/60 HZ
					25 WATTS

REVERSED CABLE

SPOT	MAIN	VCR	IN	COM	OUT	N N H
						O C C S
AUX		OUT	IN
			ALARMS

SVHS SVHS 1 2 3 4 5 6 7 8 9 10 11121314 1516

110-240V 50/60 Hz

MONITOR SIGNAL OUT

GENEX MULTIPLEXER STRAIGHT CABLE

SPOT	MAIN	VCR	IN COM		OUT N N H
						O C C S
AUX		OUT	IN
			ALARMS
						110-240V 50/60 Hz	GENEX MULTIPLEXER
	SVHS	SVHS	1 2 3 4 5	6 7	8	9 10 11121314 1516
GENEX MULTIPLEXER						STRAIGHT CABLE	RJ-45 PIN-OUTS

CM6800E-48X8 COM 4

RJ-45 PIN-OUTS

SPOT	MAIN	VCR	IN	COM		OUT		N N H
								O C C S
AUX		OUT	IN
			ALARMS
	SVHS	SVHS						110-240V 50/60 Hz
			1 2 3 4 5		6 7	8	9 10 11121314 1516

GENEX MULTIPLEXER

GENEX MULTIPLEXERS-8 MAXIMUM

Rx+ 1	1	Rx+
Rx- 2	2	Rx-
12VAC (OUT) 3	3	NC
12VAC (OUT) 4	4	NC
GROUND 5	5	GROUND
NC 6	6	NC
Tx- 7	7	Tx-
Tx+ 8	8	Tx+

Figure 25. Connecting Genex Multiplexers

32 C1528M-F (6/05)