EN 55022 1998, Class A, Note | Perle Systems 5500208-41 specification

Copyright Statement

This document must not be reproduced in any way whatsoever, either printed or electronically, without the consent of:

Perle Systems Limited,

60 Renfrew Drive

Markham, ON

Canada

L3R 0E1

Perle reserves the right to make changes without further notice, to any products to improve reliability, function, or design.

Perle, the Perle logo, and IOLAN are trademarks of Perle Systems Limited.

Microsoft, Windows 98, Windows NT, Windows 2000, Windows Server 2003, Windows XP, and Internet Explorer are trademarks of Microsoft Corporation.

Perle Systems Limited, 2004-2009.

FCC Note The IOLAN Device Server has been found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions in this Guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his/her own expense.

EN 55022: 1998, Class A, Note

WARNING This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Caution: The IOLAN Device Server is approved for commercial use only.

Image 2

Perle Systems 5500208-41 manual EN 55022 1998, Class A, Note

Contents

Iolan DS1/TS2 EN 55022 1998, Class A, Note Table of Contents User Commands Line Commands Network Commands Time Commands Statistic Commands Channel Control Commands Glossary Iolan DS1/TS2 CLI Reference Guide, Version Intended Audience PrefaceAbout This Book Contacting Technical Support Making a Technical Support Query Repair Procedure Feedback on this Manual Contacting Technical Support Introduction Command SyntaxIntroduction CLI Conventions Command Shortcuts Command Options Set Custom-App Server CommandsServer Commands Set Server Oem-login Bypass-passwordDhcp/bootp Password-limit Prompt-with-name Set ServiceTimeout Single-telnet Hardware Commands Modbus Commands Set Modbus Gateway Set TruePort Remap-Baud TruePort Baud CommandsUser Level Admin Show TruePort Show IPv6 IPv6 CommandsSet IPv6 Add Custom-IPv6 Set Custom-IPv6 Delete Custom-IPv6 Range Default 64 method manualRange Default Field Format IPv6 address prefix-bits manual IPv6 Commands User Commands Commands for Users Logged Into the Iolan Resume MenuPing Screen Set User Set User Session Show Sessions Show Line UsersSyslog Console Show Termtype Telnet Tcpport Version Configuring UsersSet Default User Add User Hotkey-prefix Level Sess-timer Line-accessService Phone-number Set User Level Show the settings for the specified user Show Default UserConfigureduser Show the settings for the current user Configuring Users Line Commands Line CommandsPort vs -Port Line Commands Set Line Options break Break-delayDial-timeout Break-length Initiate-connection Data-logginInitial Internet-address Default 10 ms ResetDefault Disabled Session strings Lock Term1, Term2, Term3 user defined terminals User Stop-bitsTerm-type Set Line Interface Serverport Set Line ServiceConfighost Hostport Initstring Set ModemModemname Line Service Commands Show Line Set Telnet-Client Options termtype Startipaddress Set UDPOutboundport Endipaddress Set Vmodem Set Vmodem-Phone IPaddress Set Modbus-Slave LineSet Modbus-Master Line Set Multihost Line Set Line Initiate-Connection Show UDP Show InterfaceShow Telnet-Client Show Vmodem Delete Modem Modem CommandsAdd Modem Show Modems Packet Forwarding Commands Set Packet-Forwarding Line Enable-end-eof1 Enable-end-trigger1Enable-end-trigger2 Enable-end-eof2 Show Packet-Forwarding Line Packet Forwarding Commands Add Community Network Commands ChapterSnmp Commands Add Trap Set Snmp Delete CommunityDelete Trap Show Snmp Tftp Commands Hosts Commands Add Gateway Gateway CommandsShow Hosts Delete Gateway Show Gateways Description Configures the gateway User Level Admin SyntaxSet Gateway Destinationip Show Syslog Logging CommandsSet Syslog Time/Date Setting Commands Time CommandsTime Commands Show Date Administration Commands Bootup Commands Configuration file Set BootupShow Bootup Show ARP Hostname/ipaddress Tftp File Transfer CommandsNetload Filename Netsave Custom Factory DefaultOptions Factory-default-config Table or a DNS server Set Motd Motd CommandsSet Show Motd Motd Commands Show Netstat Statistic Commands ChapterConfiguration Statistics Show Modbus Statistics Run-Time Statistics Set IO UDP O CommandsGlobal I/O Commands Set IO Failsafe Set IO Temperature-ScaleSet Line Set IO Modbus Set IOChannel Digital I/O Set IOChannel ModeSet IOChannel Set IOChannel Digital Input Set IOChannel Digital Input Serial Pins Description can be up to 20 characters Current status. The default is disabledSet IOChannel Digital Output Will be displayed as active Active-to-inactive-delay Active-signal-widthInactive-signal-width Inactive-to-active-delay Options description Set IOChannel Digital Output Serial PinsSet IOChannel Relay Relaynumber Set IOChannel Analog True Analog Options analogchannel Clear-mode Trigger-typeTrigger-level Clear-level Set IOChannel Analog Temperature Level Set IOChannel IOExtension EnabledDefault Disabled keepalive Options channel Server-initiated tcp-port Client-initiated tcp-portClient-initiated multihost Local-connection inputchannel Kill IOChannel Set IOChannel MultihostShow IOChannel Status Channel Show IO Show IOChannel Digital Input Channel Control CommandsDigital Output Relay Glossary