Custom Factory Default, Netsave | Perle Systems 5500208-41 specification

Custom Factory Default

Netsave

Description	Transfers a file from the IOLAN to a remote host using the TFTP protocol.
User Level	Admin
Syntax	netsave configurationcrashserialt-buftext-config
	<hostname/ip_address> <filename>
Options	configuration
	Specifies that you are going to upload a configuration file from the IOLAN to the
	specified host or IP address.
	crash
	Specifies that you are going to upload a crash file from the IOLAN to the specified host
	or IP address.
	serialt-buf
	Specifies that you are going to upload the contents of the serial trace buffer.
	text-config
	Saves the current configuration to a text file on a TFTP server.
	<hostname/ip_address>
	The IP address or host name for where the file you are uploading from the IOLAN is
	going. If you are using a host name, it must be resolved in either the IOLAN’s Host
	Table or a DNS server.
	<filename>
	The complete path and file name (cannot use a drive letter) for the file you are
	uploading from the IOLAN.

Custom Factory Default

Netload

Description	Transfers a file from a remote host to the IOLAN using the TFTP protocol.
User Level	Admin
Syntax	netload factory-default-config <hostname/IP_address> <filename>
Options	factory-default-config
	Specifies the configuration file that you are going to load from a TFTP server to the
	IOLAN that will act as the factory default configuration. See the User Guide for
	directions on how to revert back to the original factory default configuration, if
	required.
	<hostname/ip_address>
	The IP address or host name where the file you are downloading to the IOLAN resides.
	If you are using a host name, it must be resolved in either the IOLAN’s Host Table or a
	DNS server.
	<filename>
	The complete path and file name (cannot use a drive letter) of the file you are
	downloading to the IOLAN.

72	IOLAN DS1/TS2 CLI Reference Guide, Version 4.1

Image 72

Perle Systems 5500208-41 manual Custom Factory Default, Netsave, Table or a DNS server, Uploading from the Iolan

Contents

Iolan DS1/TS2 EN 55022 1998, Class A, Note Table of Contents User Commands Line Commands Network Commands Time Commands Statistic Commands Channel Control Commands Glossary Iolan DS1/TS2 CLI Reference Guide, Version Preface About This BookIntended Audience Contacting Technical Support Making a Technical Support Query Repair Procedure Feedback on this Manual Contacting Technical Support Command Syntax IntroductionIntroduction CLI Conventions Command Shortcuts Command Options Server Commands Server CommandsSet Custom-App Set Server Bypass-password Dhcp/bootpOem-login Password-limit Set Service TimeoutPrompt-with-name Single-telnet Hardware Commands Modbus Commands Set Modbus Gateway TruePort Baud Commands User Level AdminSet TruePort Remap-Baud Show TruePort IPv6 Commands Set IPv6Show IPv6 Add Custom-IPv6 Set Custom-IPv6 Range Default 64 method manual Range DefaultDelete Custom-IPv6 Field Format IPv6 address prefix-bits manual IPv6 Commands User Commands Commands for Users Logged Into the Iolan Menu PingResume Screen Set User Set User Session Show Line Users Syslog ConsoleShow Sessions Show Termtype Telnet Tcpport Configuring Users Set Default UserVersion Add User Hotkey-prefix Level Line-access ServiceSess-timer Phone-number Set User Level Show Default User ConfigureduserShow the settings for the specified user Show the settings for the current user Configuring Users Line Commands Port vs -Port Line CommandsLine Commands Set Line Break-delay Dial-timeoutOptions break Break-length Data-loggin InitialInitiate-connection Internet-address Reset Default Disabled Session stringsDefault 10 ms Lock Stop-bits Term-typeTerm1, Term2, Term3 user defined terminals User Set Line Interface Set Line Service ConfighostServerport Hostport Set Modem ModemnameInitstring Line Service Commands Show Line Set Telnet-Client Options termtype Set UDP OutboundportStartipaddress Endipaddress Set Vmodem Set Vmodem-Phone Set Modbus-Slave Line Set Modbus-Master LineIPaddress Set Multihost Line Set Line Initiate-Connection Show Interface Show Telnet-ClientShow UDP Show Vmodem Modem Commands Add ModemDelete Modem Show Modems Packet Forwarding Commands Set Packet-Forwarding Line Enable-end-trigger1 Enable-end-trigger2Enable-end-eof1 Enable-end-eof2 Show Packet-Forwarding Line Packet Forwarding Commands Network Commands Chapter Snmp CommandsAdd Community Add Trap Delete Community Delete TrapSet Snmp Show Snmp Tftp Commands Hosts Commands Gateway Commands Show HostsAdd Gateway Delete Gateway Description Configures the gateway User Level Admin Syntax Set GatewayShow Gateways Destinationip Logging Commands Set SyslogShow Syslog Time Commands Time CommandsTime/Date Setting Commands Show Date Administration Commands Bootup Commands Set Bootup Show BootupConfiguration file Show ARP Tftp File Transfer Commands NetloadHostname/ipaddress Filename Custom Factory Default Options Factory-default-configNetsave Table or a DNS server Motd Commands SetSet Motd Show Motd Motd Commands Statistic Commands Chapter Configuration StatisticsShow Netstat Show Modbus Statistics Run-Time Statistics O Commands Global I/O CommandsSet IO UDP Set IO Temperature-Scale Set LineSet IO Failsafe Set IO Modbus Set IOChannel Mode Set IOChannelSet IOChannel Digital I/O Set IOChannel Digital Input Set IOChannel Digital Input Serial Pins Current status. The default is disabled Set IOChannel Digital OutputDescription can be up to 20 characters Will be displayed as active Active-signal-width Inactive-signal-widthActive-to-inactive-delay Inactive-to-active-delay Set IOChannel Digital Output Serial Pins Set IOChannel RelayOptions description Relaynumber Set IOChannel Analog True Analog Options analogchannel Trigger-type Trigger-levelClear-mode Clear-level Set IOChannel Analog Temperature Level Enabled Default Disabled keepaliveSet IOChannel IOExtension Options channel Client-initiated tcp-port Client-initiated multihostServer-initiated tcp-port Local-connection inputchannel Set IOChannel Multihost Show IOChannel StatusKill IOChannel Channel Show IO Show IOChannel Channel Control Commands Digital OutputDigital Input Relay Glossary