Tftp File Transfer Commands, Netload | Perle Systems 5500208-41

TFTP File Transfer Commands

TFTP File Transfer Commands

Netload

Description	Transfers a file from a remote host to the IOLAN using the TFTP protocol.
User Level	Admin
Syntax	netload text-configfactory-default-configfirmwareconfiguration
	customlangterm1term2term3customapp-file
	<hostname/ip_address> <filename>

Options text-config

Specify this option if you are uploading a text-based configuration file to the IOLAN from a TFTP server.

factory-default-config

Specifies the configuration file that you are going to load from a TFTP server to the IOLAN that will act as the factory default configuration. See the User Guide for directions on how to revert back to the original factory default configuration, if required.

firmware

Specifies that you are going to download a new firmware file to the IOLAN. configuration

Specifies that you are going to download a new configuration file to the IOLAN. customlang

Specifies that you are going to download a custom language file to the IOLAN. term1term2term3

You can create and download up to three custom terminal definitions to the IOLAN. customapp-file

You can download multiple SDK program executables and ancillary files using this command by running the command multiple times to download multiple files. Use the shell CLI command as described in the SDK Programmer’s Guide to manage the files that you download.

<hostname/ip_address>

The IP address or host name where the file you are downloading to the IOLAN resides.

If you are using a host name, it must be resolved in either the IOLAN’s Host Table or a

DNS server.

<filename>

The complete path and file name (cannot use a drive letter) of the file you are downloading to the IOLAN.

71

Image 71

Perle Systems 5500208-41 manual Tftp File Transfer Commands, Netload, Hostname/ipaddress, Filename

Contents

Iolan DS1/TS2 EN 55022 1998, Class A, Note Table of Contents User Commands Line Commands Network Commands Time Commands Statistic Commands Glossary Channel Control Commands Iolan DS1/TS2 CLI Reference Guide, Version Intended Audience PrefaceAbout This Book Making a Technical Support Query Contacting Technical Support Feedback on this Manual Repair Procedure Contacting Technical Support CLI Conventions Command SyntaxIntroduction Introduction Command Options Command Shortcuts Set Server Server CommandsServer Commands Set Custom-App Password-limit Bypass-passwordDhcp/bootp Oem-login Single-telnet Set ServiceTimeout Prompt-with-name Hardware Commands Set Modbus Gateway Modbus Commands Show TruePort TruePort Baud CommandsUser Level Admin Set TruePort Remap-Baud Show IPv6 IPv6 CommandsSet IPv6 Set Custom-IPv6 Add Custom-IPv6 Field Format IPv6 address prefix-bits manual Range Default 64 method manualRange Default Delete Custom-IPv6 IPv6 Commands Commands for Users Logged Into the Iolan User Commands Screen MenuPing Resume Set User Session Set User Show Termtype Show Line UsersSyslog Console Show Sessions Tcpport Telnet Add User Configuring UsersSet Default User Version Level Hotkey-prefix Phone-number Line-accessService Sess-timer Set User Level Show the settings for the current user Show Default UserConfigureduser Show the settings for the specified user Configuring Users Set Line Line CommandsPort vs -Port Line Commands Line Commands Break-length Break-delayDial-timeout Options break Internet-address Data-logginInitial Initiate-connection Lock ResetDefault Disabled Session strings Default 10 ms Term1, Term2, Term3 user defined terminals User Stop-bitsTerm-type Set Line Interface Serverport Set Line ServiceConfighost Hostport Initstring Set ModemModemname Show Line Line Service Commands Options termtype Set Telnet-Client Endipaddress Set UDPOutboundport Startipaddress Set Vmodem Set Vmodem-Phone IPaddress Set Modbus-Slave LineSet Modbus-Master Line Set Line Initiate-Connection Set Multihost Line Show Vmodem Show InterfaceShow Telnet-Client Show UDP Show Modems Modem CommandsAdd Modem Delete Modem Set Packet-Forwarding Line Packet Forwarding Commands Enable-end-eof2 Enable-end-trigger1Enable-end-trigger2 Enable-end-eof1 Show Packet-Forwarding Line Packet Forwarding Commands Add Trap Network Commands ChapterSnmp Commands Add Community Show Snmp Delete CommunityDelete Trap Set Snmp Hosts Commands Tftp Commands Delete Gateway Gateway CommandsShow Hosts Add Gateway Destinationip Description Configures the gateway User Level Admin SyntaxSet Gateway Show Gateways Show Syslog Logging CommandsSet Syslog Time/Date Setting Commands Time CommandsTime Commands Show Date Bootup Commands Administration Commands Show ARP Set BootupShow Bootup Configuration file Filename Tftp File Transfer CommandsNetload Hostname/ipaddress Table or a DNS server Custom Factory DefaultOptions Factory-default-config Netsave Show Motd Motd CommandsSet Set Motd Motd Commands Show Modbus Statistics Statistic Commands ChapterConfiguration Statistics Show Netstat Run-Time Statistics Set IO UDP O CommandsGlobal I/O Commands Set IO Modbus Set IO Temperature-ScaleSet Line Set IO Failsafe Set IOChannel Digital Input Set IOChannel ModeSet IOChannel Set IOChannel Digital I/O Set IOChannel Digital Input Serial Pins Will be displayed as active Current status. The default is disabledSet IOChannel Digital Output Description can be up to 20 characters Inactive-to-active-delay Active-signal-widthInactive-signal-width Active-to-inactive-delay Relaynumber Set IOChannel Digital Output Serial PinsSet IOChannel Relay Options description Options analogchannel Set IOChannel Analog True Analog Clear-level Trigger-typeTrigger-level Clear-mode Set IOChannel Analog Temperature Level Options channel EnabledDefault Disabled keepalive Set IOChannel IOExtension Local-connection inputchannel Client-initiated tcp-portClient-initiated multihost Server-initiated tcp-port Channel Set IOChannel MultihostShow IOChannel Status Kill IOChannel Show IOChannel Show IO Relay Channel Control CommandsDigital Output Digital Input Glossary