Administration Commands, Bootup Commands | Perle Systems 5500208-41

7 Administration Commands

Chapter 7

This chapter defines all the CLI commands associated with configuring the IOLAN’s administration parameters.

Bootup Commands

Reboot

Description	Reboots the IOLAN. You will be prompted to save configuration to FLASH, if there
User Level	have been unsaved configuration changes.
User Level	Admin
Syntax	reboot

Reset

Description	Resets the user profile or serial line to the default factory configuration.
User Level	Admin
Syntax	reset user .<username>*
	reset line

Reset Factory

Description Resets the IOLAN to the factory configuration.

User Level Admin

Syntax reset factory

Save

Description Saves the configuration to FLASH.

User Level Admin

Syntax save

IOLAN DS1/TS2 CLI Reference Guide, Version 4.1

Page 69

Image 69

Perle Systems 5500208-41 manual Administration Commands, Bootup Commands

Contents

Iolan DS1/TS2 EN 55022 1998, Class A, Note Table of Contents User Commands Line Commands Network Commands Time Commands Statistic Commands Glossary Channel Control Commands Iolan DS1/TS2 CLI Reference Guide, Version Preface About This BookIntended Audience Making a Technical Support Query Contacting Technical Support Feedback on this Manual Repair Procedure Contacting Technical Support Introduction Command SyntaxIntroduction CLI Conventions Command Options Command Shortcuts Server Commands Server CommandsSet Custom-App Set Server Dhcp/bootp Bypass-passwordOem-login Password-limit Timeout Set ServicePrompt-with-name Single-telnet Hardware Commands Set Modbus Gateway Modbus Commands User Level Admin TruePort Baud CommandsSet TruePort Remap-Baud Show TruePort IPv6 Commands Set IPv6Show IPv6 Set Custom-IPv6 Add Custom-IPv6 Range Default Range Default 64 method manualDelete Custom-IPv6 Field Format IPv6 address prefix-bits manual IPv6 Commands Commands for Users Logged Into the Iolan User Commands Ping MenuResume Screen Set User Session Set User Syslog Console Show Line UsersShow Sessions Show Termtype Tcpport Telnet Set Default User Configuring UsersVersion Add User Level Hotkey-prefix Service Line-accessSess-timer Phone-number Set User Level Configureduser Show Default UserShow the settings for the specified user Show the settings for the current user Configuring Users Port vs -Port Line Commands Line CommandsLine Commands Set Line Dial-timeout Break-delayOptions break Break-length Initial Data-logginInitiate-connection Internet-address Default Disabled Session strings ResetDefault 10 ms Lock Stop-bits Term-typeTerm1, Term2, Term3 user defined terminals User Set Line Interface Set Line Service ConfighostServerport Hostport Set Modem ModemnameInitstring Show Line Line Service Commands Options termtype Set Telnet-Client Outboundport Set UDPStartipaddress Endipaddress Set Vmodem Set Vmodem-Phone Set Modbus-Slave Line Set Modbus-Master LineIPaddress Set Line Initiate-Connection Set Multihost Line Show Telnet-Client Show InterfaceShow UDP Show Vmodem Add Modem Modem CommandsDelete Modem Show Modems Set Packet-Forwarding Line Packet Forwarding Commands Enable-end-trigger2 Enable-end-trigger1Enable-end-eof1 Enable-end-eof2 Show Packet-Forwarding Line Packet Forwarding Commands Snmp Commands Network Commands ChapterAdd Community Add Trap Delete Trap Delete CommunitySet Snmp Show Snmp Hosts Commands Tftp Commands Show Hosts Gateway CommandsAdd Gateway Delete Gateway Set Gateway Description Configures the gateway User Level Admin SyntaxShow Gateways Destinationip Logging Commands Set SyslogShow Syslog Time Commands Time CommandsTime/Date Setting Commands Show Date Bootup Commands Administration Commands Show Bootup Set BootupConfiguration file Show ARP Netload Tftp File Transfer CommandsHostname/ipaddress Filename Options Factory-default-config Custom Factory DefaultNetsave Table or a DNS server Set Motd CommandsSet Motd Show Motd Motd Commands Configuration Statistics Statistic Commands ChapterShow Netstat Show Modbus Statistics Run-Time Statistics O Commands Global I/O CommandsSet IO UDP Set Line Set IO Temperature-ScaleSet IO Failsafe Set IO Modbus Set IOChannel Set IOChannel ModeSet IOChannel Digital I/O Set IOChannel Digital Input Set IOChannel Digital Input Serial Pins Set IOChannel Digital Output Current status. The default is disabledDescription can be up to 20 characters Will be displayed as active Inactive-signal-width Active-signal-widthActive-to-inactive-delay Inactive-to-active-delay Set IOChannel Relay Set IOChannel Digital Output Serial PinsOptions description Relaynumber Options analogchannel Set IOChannel Analog True Analog Trigger-level Trigger-typeClear-mode Clear-level Set IOChannel Analog Temperature Level Default Disabled keepalive EnabledSet IOChannel IOExtension Options channel Client-initiated multihost Client-initiated tcp-portServer-initiated tcp-port Local-connection inputchannel Show IOChannel Status Set IOChannel MultihostKill IOChannel Channel Show IOChannel Show IO Digital Output Channel Control CommandsDigital Input Relay Glossary