Line Service Commands, Show Line | Perle Systems 5500208-41 specs

Line Service Commands

Set Termtype

Description Sets the terminal type for the current terminal session. term1, term2, and term3 refer to the user-uploadable custom terminal definitions. If these are not present, the default is wyse60.

User Level Restricted, Normal, Admin

Syntax set termtype [wyse60vt100ansidumbtvi925ibm3151tevt320hp700term1term2 term3]

Option wyse60vt100ansidumbtvi925ibm3151tevt320hp700term1term2term3

Specifies the type of terminal connected to the line:

zDumb

zWYSE60

zVT100

zANSI

zTVI925

zIBM3151TE

zVT320 (specifically supporting VT320-7)

zHP700 (specifically supporting HP700/44)

zTerm1, Term2, Term3 (user defined terminals)

Show Line

Description	Shows the line settings/information.
User Level	Admin
Syntax	show line

Line Service Commands

Set Custom-App

Description	You can create a custom application that can run on a specific serial line in IOLAN
User Level	using the Perle SDK.
User Level	Admin
Syntax	set custom-app line .<number>* program-command-line <command>
Options	program-command-line
	The name of the SDK program executable that has been already been downloaded to
	the IOLAN, plus any parameters you want to pass to the program. Maximum of 80
	characters. Use the shell CLI command as described in the SDK Programmer’s Guide
	to manage the files that you have downloaded to the IOLAN. For example, using
	sample outraw program, you would type:
	outraw 192.168.2.1:10001 Acct:10001
	if you were starting the application on a line.

48	IOLAN DS1/TS2 CLI Reference Guide, Version 4.1

Image 48

Perle Systems 5500208-41 manual Line Service Commands, Show Line

Contents

Iolan DS1/TS2 EN 55022 1998, Class A, Note Table of Contents User Commands Line Commands Network Commands Time Commands Statistic Commands Channel Control Commands Glossary Iolan DS1/TS2 CLI Reference Guide, Version Preface About This BookIntended Audience Contacting Technical Support Making a Technical Support Query Repair Procedure Feedback on this Manual Contacting Technical Support Command Syntax IntroductionIntroduction CLI Conventions Command Shortcuts Command Options Server Commands Server CommandsSet Custom-App Set Server Bypass-password Dhcp/bootpOem-login Password-limit Set Service TimeoutPrompt-with-name Single-telnet Hardware Commands Modbus Commands Set Modbus Gateway TruePort Baud Commands User Level AdminSet TruePort Remap-Baud Show TruePort IPv6 Commands Set IPv6Show IPv6 Add Custom-IPv6 Set Custom-IPv6 Range Default 64 method manual Range DefaultDelete Custom-IPv6 Field Format IPv6 address prefix-bits manual IPv6 Commands User Commands Commands for Users Logged Into the Iolan Menu PingResume Screen Set User Set User Session Show Line Users Syslog ConsoleShow Sessions Show Termtype Telnet Tcpport Configuring Users Set Default UserVersion Add User Hotkey-prefix Level Line-access ServiceSess-timer Phone-number Set User Level Show Default User ConfigureduserShow the settings for the specified user Show the settings for the current user Configuring Users Line Commands Port vs -Port Line CommandsLine Commands Set Line Break-delay Dial-timeoutOptions break Break-length Data-loggin InitialInitiate-connection Internet-address Reset Default Disabled Session stringsDefault 10 ms Lock Stop-bits Term-typeTerm1, Term2, Term3 user defined terminals User Set Line Interface Set Line Service ConfighostServerport Hostport Set Modem ModemnameInitstring Line Service Commands Show Line Set Telnet-Client Options termtype Set UDP OutboundportStartipaddress Endipaddress Set Vmodem Set Vmodem-Phone Set Modbus-Slave Line Set Modbus-Master LineIPaddress Set Multihost Line Set Line Initiate-Connection Show Interface Show Telnet-ClientShow UDP Show Vmodem Modem Commands Add ModemDelete Modem Show Modems Packet Forwarding Commands Set Packet-Forwarding Line Enable-end-trigger1 Enable-end-trigger2Enable-end-eof1 Enable-end-eof2 Show Packet-Forwarding Line Packet Forwarding Commands Network Commands Chapter Snmp CommandsAdd Community Add Trap Delete Community Delete TrapSet Snmp Show Snmp Tftp Commands Hosts Commands Gateway Commands Show HostsAdd Gateway Delete Gateway Description Configures the gateway User Level Admin Syntax Set GatewayShow Gateways Destinationip Logging Commands Set SyslogShow Syslog Time Commands Time CommandsTime/Date Setting Commands Show Date Administration Commands Bootup Commands Set Bootup Show BootupConfiguration file Show ARP Tftp File Transfer Commands NetloadHostname/ipaddress Filename Custom Factory Default Options Factory-default-configNetsave Table or a DNS server Motd Commands SetSet Motd Show Motd Motd Commands Statistic Commands Chapter Configuration StatisticsShow Netstat Show Modbus Statistics Run-Time Statistics O Commands Global I/O CommandsSet IO UDP Set IO Temperature-Scale Set LineSet IO Failsafe Set IO Modbus Set IOChannel Mode Set IOChannelSet IOChannel Digital I/O Set IOChannel Digital Input Set IOChannel Digital Input Serial Pins Current status. The default is disabled Set IOChannel Digital OutputDescription can be up to 20 characters Will be displayed as active Active-signal-width Inactive-signal-widthActive-to-inactive-delay Inactive-to-active-delay Set IOChannel Digital Output Serial Pins Set IOChannel RelayOptions description Relaynumber Set IOChannel Analog True Analog Options analogchannel Trigger-type Trigger-levelClear-mode Clear-level Set IOChannel Analog Temperature Level Enabled Default Disabled keepaliveSet IOChannel IOExtension Options channel Client-initiated tcp-port Client-initiated multihostServer-initiated tcp-port Local-connection inputchannel Set IOChannel Multihost Show IOChannel StatusKill IOChannel Channel Show IO Show IOChannel Channel Control Commands Digital OutputDigital Input Relay Glossary