Pioneer VSA-AX10 5Select the name of the company that, makes your component, Basic

Remote Control of Other Components

	Preset Recall [ DVD/LD]			BACK	SETUP
					REMOTE
AMP		SELECT MAKER
					CD
DVD/LD	ITEM	PIONEER	TOSHIBA	SHARP	CD-R/
					TAPE1
	DVD
VCR1		PANA-		SAM-	TUNER
/DVR			SONY
	MAKER	SONIC		SUNG
VCR2					VIDEO
VCR3	PIONEER VICTOR		AKAI	DENON	SAT
TV			PAGE		TV
			1 / 2		CONTROL

		5
	6
	Preset Recall [ DVD/LD]		BACK	SETUP
				REMOTE
AMP	ITEM	SELECT NUMBER		CD
DVD/LD	DVD			CD-R/
	1	2		TAPE1
/DVR				TUNER
	MAKER
VCR1
VCR2	PIONEER			VIDEO
VCR3	NUMBER			SAT
	1		SETUP	TV
TV			OK	CONTROL

7

«

5Select the name of the company that

makes your component.

If there are two pages of company names, use the page +/– buttons to go back and forth between the two sets of makers' names. For explanation purposes, we'll use PIONEER as an example.

6Press the number 1 button.

If the component you are trying to control turns on/off, the setup for this component is complete, but compo- nents that don't have a standby mode can't respond in this way. To test if you've set it up properly work through step 8. Then try using selecting the function you just setup (for example a CD player) and using the controls on this remote control. If the component does not respond, try working through the procedure again and pressing number 2 instead this time. Continue this procedure until one of the commands works.

If none of the commands seem to work, try the learning mode to program the component into the remote control. This is explained on the following page.

To go back a screen

press the BACK button.

To exit the process without inputting the commands

press the BACK button repeatedly.

7Press the SETUP OK button and the screen returns to SELECT FUNCTION so you can program another component into the remote control.

		9
	Preset Recall	BACK SETUP
		REMOTE
AMP
		CD
DVD/LD		CD-R/
		TAPE1
VCR1		TUNER
/DVR	SELECT FUNCTION
VCR2		VIDEO
VCR3		SAT
TV		TV
		CONTROL

Naturally it's easiest and most logical to assign the button that has the same name as the component you are setting up (for example, choose the DVD/LD button for your DVD player).

You may find you have components which do not correspond to the name on any MULTI CONTROL button (for example a cable TV tuner) or you have two compo- nents where only one button is provided (for example, CD-R/TAPE 1). In this case, use step 3 to assign any available MULTI CONTROL button to the component you want to remote control.

For example, you may have both a CD-R and a tape deck in your system but only one video deck. It would make sense to assign the CD-R/TAPE 1 MULTI CONTROL button to the CD-R and the VCR 2 MULTI CONTROL button to your tape deck. To do this choose VCR 2 in step 3 when you want to set up the tape deck. Then choose TAPE in step 4 and proceed as above. The only practical difference in this method is that you have to remember the VCR 2 MULTI CONTROL button is actually your tape deck.

In this case, you would need to hook up your tape deck to the input jacks marked VCR 2 on the back of the amplifier.

This method should help you customize the remote control for your system and let you control all of your components with the remote control for the VSA-AX10.

BASIC

8Repeat the process from step 2 for all of your components.

9Press the BACK button repeatedly to

leave the REMOTE SETUP mode. 61

En