Advanced Setup
Assigning the Component Video Inputs
If you used component video cords (and only if you did so) to connect any equipment you must tell the amplifier which device is hooked up with this special kind of cable. If you did not use component video cord (which is a specialized cord that separates the video signal into two color spectrums and a light spectrum for transmission) then you don't need to worry about the procedure below. The default settings for the component video inputs are as follows: 1= off; 2= off; 3= off.
1 
AMP
DVD/LD
VCR1
/DVR
VCR2
VCR3
3 
TV
|
|
|
| 2 |
Amplifier | MAIN | SUB | SETUP | |
|
|
|
| REMOTE |
TONE | BASS/ |
|
| CD |
ATREBLE |
|
|
| |
|
|
| ||
|
|
|
| |
|
| EFFECT/ | TAPE1 | |
|
|
| ||
DISPLAY | VIDEO | CH SEL. | TUNER | |
DIMMER | SELECT |
|
|
|
| SPEAKER |
| INPUT | VIDEO |
STATUS | LOUDNESS |
| ||
| A/B |
| ATT. | SAT |
SYSTEM |
| TAPE 2 | SIGNAL | TV |
SETUP |
| MONITOR | SELECT | CONTROL |
1 | Turn on the amplifier and your TV, |
| press the AMP on the remote |
| control. |
|
|
2 | Press the SUB button on the remote |
| control. |
|
|
3 | Press the SYSTEM SETUP button. |
4 | System Setup |
|
|
|
|
| ||
|
|
|
|
|
| |||
| [ Auto Surround Setup ] |
| ||||||
| [ |
| ] |
|
|
| ||
| 1. Input Assign |
|
|
| ||||
| [2. Surround Setup] |
| ||||||
| [3. Expert Setup] |
|
|
| ||||
| [4. THX Audio Setup] |
| ||||||
| [Exit] |
|
|
|
|
| ||
5 | 1.Input Assign |
|
|
| ||||
| [ |
| ||||||
| [ | 2.C'nent VideoIn | ] |
| ||||
| [Return] |
|
|
|
|
| ||
6 | 1.2. C' nent Video |
| In |
| ||||
|
| C' |
|
| ] | |||
| DVD/LD[ | |||||||
|
| C' | [ | OFF | ] | |||
|
| C' | [ | OFF | ] | |||
[Return]
4 | Looking at the |
| your TV, use the 5∞ buttons to |
| select INPUT ASSIGN. Press the |
| ENTER button. |
|
|
5 | Use the 5∞ buttons to select |
| C'NENT VIDEO IN. Press the ENTER |
| button. |
|
|
6 | Use the 5∞ buttons to move |
| through the different component |
| video input settings and use the 2 3 |
| buttons to select the component |
| that you hooked up to that |
component video in.
If you're not sure which component is connected to which component video in, look on the back of the amplifier and check the cables you connected.
7 | 1.2. C' nent Video In |
| |
| C' | [ DVD/LD ] | |
| C' | [ VCR1 | ] |
| C' | [ OFF | ] |
[Return]
memo
If you connect the TV monitor with compo- nent video cord, and the DVD player with composite or S video cord then you should set that terminal to off.
7When you're finished use the 5∞ buttons to select RETURN and press
ENTER.
You will leave the "Assigning the Component Video Inputs" mode.
8Use the 5∞ buttons to select
RETURN and press ENTER, again. Then, use the 5∞ buttons to select
EXIT and press ENTER.
EXPERT
81
En
