Speciﬁcations, Equipment Specifications | Pitney Bowes DA950

Speciﬁcations

Equipment Specifications

Physical Dimensions

16" (406.4mm) high; 30" (762mm) wide; 24" (609.6mm) deep

Weight

87 lbs. (39.5 kg), including accessories

Electrical

Voltage: 120 volts AC +/- 10%. Other selectable voltages: 100v, 220v, and 240v

Frequency: 60 Hz +/- 3 Hz automatic frequency selection for other voltages

Fuse Type: 2 x 2 Amp Slow-Blow

Power Consumption: 126 Watts, 430 BTU/hr.

Agency Approvals

Pitney Bowes certifies that the Address Printer complies with the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC. The product was

tested in a typical configuration.

Interface

Centronics Parallel and USB

Control Language

PCL5, modified

Driver Compatibility

Windows 2000, XP

Address Recovery

Memory buffer holds a maximum of 99 addresses

B-2

Image 102

Pitney Bowes DA950 manual Speciﬁcations, Equipment Specifications

Contents

Page FCC Compliance Contents Chapter Using the DA950 with Your Computer Chapter Troubleshooting Your Printer Appendix B DA950 Specifications Chapter Welcome to the DA950 Printer Using This Guide Overview Appendix B-Specifications TroubleshootingAppendix A-Using the Control Panel Menus System Requirements Phone Support Getting Help Ordering SuppliesWorld Wide Web Before You Contact Pitney Bowes Important Safety Notes Overview Printer Parts and Locations Printer Parts and Locations Feeder Parts and Locations Feeder Parts and Locations Setting Up Your DA950 Printer Setup Choosing a Location Assembling the Printer Install the Feeder Install the Shock Install the Side Guides Install the Feed Ramp Setup Printer Connecting the Parallel Cable or USB CableAssembling Parallel Cable Connect the Power Cord and Turn on Install the Bulk Ink Assembly Optional Install the Print Cartridges Printer Basics Setting Up a Job BasicsSet the Separator Gap Setting the Proper Feed Gap Tips for Setting the Separators Center the Feed Ramp under the Material Set the Feed Angle Set the Feed Ramp Length Position the Side Guides Load Material Adjust the Media Thickness Knob Output Stacker Print a Test Piece Set the Print Head Position Adjust the Takeaway Roller Tension Basics Using the DA950 with Your Computer Using the Printer with Your Computer Installing the Printer Driver Selecting DA950 Printer From Windows Application Making DA950 Default Print Driver Accessing the Print DriverAbout Envelope Designer Plus General Tab Printing Preferences Paper TabPaper Size Orientation Feed Delay Printing PreferencesFeautures Tab Print Quality Letter 300 dpi Draft 200 dpiMemory Overlay Advanced Tab Pause on Tray BreakPause on Package Break Printer Maintenance Printer Maintenance Replacing Print CartridgesRemoving Old Print Cartridges Installing New Print Cartridges Removing the Old Bulk Ink Cartridges Installing New Bulk Ink Cartridges Prolonging Life Print Cartridges Cleaning Print Quality Problems Preventive Maintenance Cleaning the Sensor Cleaning Exit Idler Entry Rollers Cleaning the Wipers Transport Belts Floor Assembly Troubleshooting Your Printer Problems and Solutions Troubleshooting Your PrinterFeed Problems Problem Intermittent Feed Problem Multifeed feeds doubles or skewing Problem No Print Problem Grey or Light Print-Black Ink Problem Address Printing is not SharpProblem Address Smudging Problem Skewed Print Problem Unwanted BoldingProblem Addresses Walking Problem Motor Turning but no Feed Roller Move Ment Interface Problems Motor Problems Other ProblemsProblem No Communications Printer Does Not Respond Problem Out of Memory Problem Paper Out or Paper Jam Troubleshooting Your Printer AppendixA Using the Control Panel Printer MenusThis Button Does This Using the Menus Enter Printer Menus Using the Main Menu Main Menu Menu Options Address Layout Distance from Left/Distance to RightDistance to Right Distance from Top Line Spacing Letter Print QualityExecutive Draft Font Selection Digit On/Off BarcodeLocation Bar Width Address Recovery Get AddressesClear Memory Load Job SettingsClear Counter Save First Image Overlay Conveyor TimeImage Overlay Clear Overlay Reset Ink Counter Purge Print Head Using the Setup Menu Setup Menu Menu Options Using the Setup Menu Stop On Feed Err ErrorFeeder Signal Lines Per Address Signal Polarity Active On/Active OffOn/Quick Off Line Termination Hex Dump Mode MSB Inch / Millimeter Symbol SetLanguage Menu Languages Postal Bundle Brk Break Enable/Disable Break Transport Speed Break Char Count Postal Bundle Brk BreakBreak Character Pause Time Periodic Purge Pre-PurgePurge at Start Purge Interval Stream Feed Feed GapSelectable Gap ROM Revision Print Head Size Using the Service Menu Adjust PrintHead 2 up down Head 3 up down Head 5 up down Head 6 up down Head 3 is now correctly aligned Head 2 misaligned horizontally Heads now aligned horizontally Bank a to Sensor/Bank B to Sensor Test System Test Display Printer Menus AppendixB Equipment Specifications Speciﬁcations Downloadable Fonts Print Modes/Print ResolutionResident Fonts User-Definable Parameters Noise Level Printhead/InkJet CartridgesEnvironmental Limits Recommended Usage Media Sizes Material SpecificationsApproved Media Material Notes Name Style Dimensions Inch Dimensions Metric Height x Width Table of Envelope Sizes AppendixC Glossary Draft quality Embedded printer commandsDouble feeding Drivers Interface cable Interface connectorInternal test address message Internal fonts Point size PCL commandsPower socket Port Subdirectory Universal Serial Bus USB Index Index Index Index Index Page