Install the Bulk Ink Assembly Optional | Pitney Bowes DA950 instruction

Setup

Assembling the Printer (continued)

7. Install the Bulk Ink Assembly (Optional)

The bulk ink assembly can accomodate up to six ink reser- voirs.

A. Assemble the bulk ink assembly. Tighten the nuts around the premounted screws.

B. Slide the bulk ink assembly onto the hooks at the back of the printer (adjacent to the power switch).

8. Install the Print Cartridge(s)

The printer uses Print Cartridges which you must now install before you can print. Follow the instructions in Chap- ter 5—Maintenance to install the new cartridges.

2-10

Image 26

Pitney Bowes DA950 manual Install the Bulk Ink Assembly Optional, Install the Print Cartridges

Contents

Page FCC Compliance Contents Chapter Using the DA950 with Your Computer Chapter Troubleshooting Your Printer Appendix B DA950 Specifications Chapter Welcome to the DA950 Printer Using This Guide Overview Appendix B-Specifications TroubleshootingAppendix A-Using the Control Panel Menus System Requirements Phone Support Getting Help Ordering SuppliesWorld Wide Web Before You Contact Pitney Bowes Important Safety Notes Overview Printer Parts and Locations Printer Parts and Locations Feeder Parts and Locations Feeder Parts and Locations Setting Up Your DA950 Printer Setup Choosing a Location Assembling the Printer Install the Feeder Install the Shock Install the Side Guides Install the Feed Ramp Setup Printer Connecting the Parallel Cable or USB CableAssembling Parallel Cable Connect the Power Cord and Turn on Install the Bulk Ink Assembly Optional Install the Print Cartridges Printer Basics Set the Separator Gap Setting Up a JobBasics Setting the Proper Feed Gap Tips for Setting the Separators Center the Feed Ramp under the Material Set the Feed Angle Set the Feed Ramp Length Position the Side Guides Load Material Adjust the Media Thickness Knob Output Stacker Print a Test Piece Set the Print Head Position Adjust the Takeaway Roller Tension Basics Using the DA950 with Your Computer Using the Printer with Your Computer Installing the Printer Driver Selecting DA950 Printer From Windows Application About Envelope Designer Plus Making DA950 Default Print DriverAccessing the Print Driver General Tab Paper Size Printing PreferencesPaper Tab Orientation Feautures Tab Feed DelayPrinting Preferences Memory Overlay Print QualityLetter 300 dpi Draft 200 dpi Pause on Package Break Advanced TabPause on Tray Break Printer Maintenance Removing Old Print Cartridges Printer MaintenanceReplacing Print Cartridges Installing New Print Cartridges Removing the Old Bulk Ink Cartridges Installing New Bulk Ink Cartridges Prolonging Life Print Cartridges Cleaning Print Quality Problems Preventive Maintenance Cleaning the Sensor Cleaning Exit Idler Entry Rollers Cleaning the Wipers Transport Belts Floor Assembly Troubleshooting Your Printer Problems and Solutions Troubleshooting Your PrinterFeed Problems Problem Intermittent Feed Problem Multifeed feeds doubles or skewing Problem No Print Problem Address Smudging Problem Grey or Light Print-Black InkProblem Address Printing is not Sharp Problem Addresses Walking Problem Skewed PrintProblem Unwanted Bolding Problem Motor Turning but no Feed Roller Move Ment Interface Problems Motor Problems Other ProblemsProblem No Communications Printer Does Not Respond Problem Out of Memory Problem Paper Out or Paper Jam Troubleshooting Your Printer AppendixA This Button Does This Using the Control PanelPrinter Menus Using the Menus Enter Printer Menus Using the Main Menu Main Menu Menu Options Distance to Right Address LayoutDistance from Left/Distance to Right Distance from Top Line Spacing Letter Print QualityExecutive Draft Font Selection Digit On/Off BarcodeLocation Bar Width Clear Memory Address RecoveryGet Addresses Load Job SettingsClear Counter Save First Image Overlay Conveyor TimeImage Overlay Clear Overlay Reset Ink Counter Purge Print Head Using the Setup Menu Setup Menu Menu Options Feeder Signal Using the Setup MenuStop On Feed Err Error Lines Per Address Signal Polarity Active On/Active OffOn/Quick Off Line Termination Hex Dump Mode MSB Inch / Millimeter Symbol SetLanguage Menu Languages Postal Bundle Brk Break Enable/Disable Break Transport Speed Break Char Count Postal Bundle Brk BreakBreak Character Pause Time Periodic Purge Pre-PurgePurge at Start Purge Interval Stream Feed Feed GapSelectable Gap ROM Revision Print Head Size Head 2 up down Head 3 up down Head 5 up down Head 6 up down Using the Service MenuAdjust Print Head 3 is now correctly aligned Head 2 misaligned horizontally Heads now aligned horizontally Bank a to Sensor/Bank B to Sensor Test System Test Display Printer Menus AppendixB Equipment Specifications Speciﬁcations Downloadable Fonts Print Modes/Print ResolutionResident Fonts User-Definable Parameters Noise Level Printhead/InkJet CartridgesEnvironmental Limits Recommended Usage Media Sizes Material SpecificationsApproved Media Material Notes Name Style Dimensions Inch Dimensions Metric Height x Width Table of Envelope Sizes AppendixC Glossary Draft quality Embedded printer commandsDouble feeding Drivers Interface cable Interface connectorInternal test address message Internal fonts Point size PCL commandsPower socket Port Subdirectory Universal Serial Bus USB Index Index Index Index Index Page