User Guide V2IU 6400-S Converged Network Appliance
April
Trademark Information
Configuring the V2IU 6400-S
Contents
Installing the 6400-S
Introduction
Configuring the Firewall
Configuring Network Settings
Configuring VoIP
Administrative Options
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Appendix-1
User Guide V2IU 6400-S Converged Network Appliance
Introduction
Introducing the V2IU 6400-S Converged Network Appliance
T-1/E-1
Service Provider
Hotspot
NxT-1/E-1
Functional features Hardware features Management features
Features
Physical Connections and Specifications
Management Features
Remote system logging VoIP and subnet routing Firewall
Administration, maintenance and upgrading
User Guide V2IU 6400-S Converged Network Appliance
Mains AC power disconnect
Installing the 6400-S
Physical Installation1
Grounding the rack installation
Overcurrent protection
If DC power supplies are installed
Main DC power disconnect
Grounding the 6400-S
Power Supplies1
DC Power Supply Interface Requirements
AC Power Supply LED Indicators
AC Power Supply Interface Requirements
DC Power Supply LED Indicators
Voltage
Connecting to the 6400-S Logging in and out of the 6400-S
Configuring the V2IU 6400-S
Connecting to the 6400-S
Navigating through the configuration pages Getting help
3. Press Return The Main Configuration Menu appears
Navigating through the configuration pages
Logging in and out of the 6400-S
Getting help
Getting information about the network
2. In the System menu, select Network Information
Routing Information
Link Status
Getting information about the system
Interface Information
System uptime
2. In the System menu, select System Information
Number of active streams
Memory Usage
Recent Call Log
Process Information
System Logging Messages
Configuring subscriber interface settings
Configuring Network Settings
Before Starting
Configuring provider interface settings
Setting the Ethernet link rate
To configure provider interface settings
To set the link rate
Configuring the Network
Configuring Network Settings
2. Enter an IP address for the Default Gateway
To configure network settings
1. In the Network page, move to the Network Settings section
3. Enter the Primary DNS Server 4. Enter the Secondary DNS Server
Configuring VoIP
2. On the VoIP ALG page, enter information as follows
To configure VoIP ALG
1. In the navigation bar, select VoIP ALG
Field
Field
Configuring VoIP
Description
Field
Description
Field
Description
Configuring VoIP subnet routing
To configure VoIP subnet routing
Deleting a VoIP subnet route
To delete a VoIP subnet route
Configuring VoIP survivability
Configuring sofswitch survivability
Description
To configure sofswitch survivability
Field
Time s between DNS lookups
Configuring VRRP
To configure VRRP
2. In the System menu, select VRRP Configuration
User Guide V2IU 6400-S Converged Network Appliance
Configuring the Firewall
Configuring the firewall basic settings
1. In the navigation pane, select Firewall
Configuring advanced firewall settings
Basic settings rules
Enabling or disabling the firewall
Advanced setting rules
1. To disable the firewall, check or uncheck the Enable Firewall box
2. Press Submit
Administrative Options
Changing the administration password
ifconfig eth020 192.168.20.10 netmask
Specifying user commands
iptables -I POSTROUTING -t nat -s 192.168.20.10 -j ACCEPT
Managing SIP, MGCP or H.323 clients
Deleting clients
Selecting a client
To work with the client list
Adding clients
2. Press OK to delete the client or Cancel to end the operation
Querying clients
To query a client
Restarting the network
Rebooting the system
Using Network Test Tools
To reboot the system
To run a ping test
Running a ping test
Running a traceroute test
To run a traceroute test
Upgrading the firmware
Configuring a management interface
Configuring the interface
2. On the System menu, select Management Interface
Reconnecting the 6400-S
4. Check the Enable Management Interface box
3. On the Management Interface page
Configuring the trusted management addresses
Figure 1. Move the connection from Port 2 to Port
Setting the Provider MTU size
To configure trusted management addresses
To enable SNMP
Enabling SNMP
To set the Provider MTU size
Field
2. In the System menu, select Services Configuration
3. Enter information as described in the following table
Description
Enabling remote system logging
To enable remote system logging
Disabling SNMP
Field
Description
Field
Remote Syslog Host
Setting the system date and time
Disabling remote system logging
Creating a static route
To configure a static route
4. Enter an IP Network address 5. Enter a Netmask address
Deleting a static route
2. In the System menu, select Route 3. Check the Apply Route box
6. Enter a Gateway address 7. Press Submit
User Guide V2IU 6400-S Converged Network Appliance
Troubleshooting Tips
Appendix
Pinging the softswitch
Telephone doesnt register with the softswitch
Checking the configurations on the ALG page
To check configurations on the ALG page
Important Safeguards
Regulatory Notices
IMPORTANT-READ CAREFULLY BEFORE USING THE SOFTWARE PRODUCT
END-USER LICENSE AGREEMENT FOR POLYCOM SOFTWARE
2. OTHER RIGHTS AND LIMITATIONS
2.5 Software Transfer. You may permanently transfer all of your rights under this Agreement in connection with transfer of the PRODUCT, provided you retain no copies, you transfer all of the SOFTWARE PRODUCT including all component parts, the media and printed materials, any upgrades, this Agreement, and, if applicable, the Certificate of Authenticity, and the recipient agrees to the terms of this Agreement. If the SOFTWARE PRODUCT is an upgrade, any transfer must include all prior versions of the SOFTWARE PRODUCT. However, if the SOFTWARE PRODUCT is marked Not for Resale or NFR, you may not resell it or otherwise transfer it for value
6. WARRANTY AND WARRANTY EXCLUSIONS
IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES, TERMS, OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, SATISFACTORY QUALITY, CORRESPONDENCE WITH DESCRIPTION, AND NON-INFRINGEMENT, ALL OF WHICH ARE EXPRESSLY DISCLAIMED. POLYCOM NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE OR USE OF THE SOFTWARE PRODUCT. NO ADVICE OR INFORMATION, WHETHER ORAL OR WRITTEN, OBTAINED BY YOU FROM POLYCOM OR THROUGH OR FROM THE SOFTWARE PRODUCT SHALL CREATE ANY WARRANTY NOT EXPRESSLY STATED IN THIS AGREEMENT
11. MISCELLANEOUS
Polycom, Inc. 2005. ALL RIGHTS RESERVED
2 above provided that you also do one of the following
the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange or
conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this
NO WARRANTY
Compliance and Compatibility1
1 Intel Telco/Industrial Grade Server TIGPR2U Product Guide
Regulatory Notices
Regulatory Notices
User Guide V2IU 6400-S Converged Network Appliance
Regulatory Notices
