Manuals / Polycom / Computer Equipment / Network Hardware

Polycom 6400-S manual Enabling SNMP, To set the Provider MTU size, To enable SNMP

Models: 6400-S

1 82

Download 82 pages 8.64 Kb

Page 59

To set the Provider MTU size:

Administrative Options

Caution When manually configuring the MTU size we recommend that you use a setting of 800 bytes or greater. You may experience problems with certain types of VoIP traffic if the MTU size is set below 800 bytes.

To set the Provider MTU size:

1.In the navigation bar, select System.

2.In the System menu, select Set Link.

3.Enter the Provider MTU size.

4.Press Submit.

Enabling SNMP

The 6400-S can be managed remotely by an SNMP network management system such as HP Openview. The 6400-S supports SNMPv1 and MIB-II (RFC1213). All MIB-II variables are read only. The MIB variables sysContact and sysLocation are set by the web GUI.

To enable SNMP:

1.In the Navigation bar, select System.

7 - 13

Image 59

Polycom 6400-S manual Enabling SNMP, To set the Provider MTU size, To enable SNMP

Contents

April User Guide V2IU 6400-S Converged Network ApplianceTrademark Information Introduction ContentsInstalling the 6400-S Configuring the V2IU 6400-SAdministrative Options Configuring Network SettingsConfiguring VoIP Configuring the FirewallAppendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Appendix-1 User Guide V2IU 6400-S Converged Network Appliance Introducing the V2IU 6400-S Converged Network Appliance IntroductionNxT-1/E-1 Service ProviderHotspot T-1/E-1Functional features Hardware features Management features Physical Connections and Specifications FeaturesManagement Features User Guide V2IU 6400-S Converged Network Appliance Administration, maintenance and upgradingRemote system logging VoIP and subnet routing Firewall Grounding the rack installation Installing the 6400-SPhysical Installation1 Mains AC power disconnectGrounding the 6400-S If DC power supplies are installedMain DC power disconnect Overcurrent protectionDC Power Supply Interface Requirements Power Supplies1Voltage AC Power Supply Interface RequirementsDC Power Supply LED Indicators AC Power Supply LED IndicatorsNavigating through the configuration pages Getting help Configuring the V2IU 6400-SConnecting to the 6400-S Connecting to the 6400-S Logging in and out of the 6400-S3. Press Return The Main Configuration Menu appears Logging in and out of the 6400-S Navigating through the configuration pagesGetting information about the network Getting helpRouting Information 2. In the System menu, select Network InformationInterface Information Getting information about the systemLink Status Number of active streams 2. In the System menu, select System InformationSystem uptime System Logging Messages Recent Call LogProcess Information Memory UsageBefore Starting Configuring Network SettingsConfiguring subscriber interface settings Configuring provider interface settings To configure provider interface settings Setting the Ethernet link rateTo set the link rate Configuring Network Settings Configuring the Network3. Enter the Primary DNS Server 4. Enter the Secondary DNS Server To configure network settings1. In the Network page, move to the Network Settings section 2. Enter an IP address for the Default GatewayConfiguring VoIP Field To configure VoIP ALG1. In the navigation bar, select VoIP ALG 2. On the VoIP ALG page, enter information as followsDescription Configuring VoIPField Description FieldDescription FieldTo configure VoIP subnet routing Configuring VoIP subnet routingTo delete a VoIP subnet route Deleting a VoIP subnet routeConfiguring sofswitch survivability Configuring VoIP survivabilityTime s between DNS lookups To configure sofswitch survivabilityField DescriptionTo configure VRRP Configuring VRRP2. In the System menu, select VRRP Configuration User Guide V2IU 6400-S Converged Network Appliance Configuring the firewall basic settings Configuring the Firewall1. In the navigation pane, select Firewall Basic settings rules Configuring advanced firewall settings2. Press Submit Advanced setting rules1. To disable the firewall, check or uncheck the Enable Firewall box Enabling or disabling the firewallChanging the administration password Administrative Optionsiptables -I POSTROUTING -t nat -s 192.168.20.10 -j ACCEPT Specifying user commandsifconfig eth020 192.168.20.10 netmask Managing SIP, MGCP or H.323 clients To work with the client list Selecting a clientDeleting clients To query a client 2. Press OK to delete the client or Cancel to end the operationQuerying clients Adding clientsTo reboot the system Rebooting the systemUsing Network Test Tools Restarting the networkTo run a traceroute test Running a ping testRunning a traceroute test To run a ping testUpgrading the firmware Configuring the interface Configuring a management interface3. On the Management Interface page Reconnecting the 6400-S4. Check the Enable Management Interface box 2. On the System menu, select Management InterfaceFigure 1. Move the connection from Port 2 to Port Configuring the trusted management addressesTo configure trusted management addresses Setting the Provider MTU sizeTo set the Provider MTU size Enabling SNMPTo enable SNMP Description 2. In the System menu, select Services Configuration3. Enter information as described in the following table FieldField To enable remote system loggingDisabling SNMP Enabling remote system loggingRemote Syslog Host FieldDescription Disabling remote system logging Setting the system date and timeTo configure a static route Creating a static route6. Enter a Gateway address 7. Press Submit Deleting a static route2. In the System menu, select Route 3. Check the Apply Route box 4. Enter an IP Network address 5. Enter a Netmask addressUser Guide V2IU 6400-S Converged Network Appliance Appendix Troubleshooting TipsTo check configurations on the ALG page Telephone doesnt register with the softswitchChecking the configurations on the ALG page Pinging the softswitchEND-USER LICENSE AGREEMENT FOR POLYCOM SOFTWARE Regulatory NoticesIMPORTANT-READ CAREFULLY BEFORE USING THE SOFTWARE PRODUCT Important Safeguards2. OTHER RIGHTS AND LIMITATIONS 2.5 Software Transfer. You may permanently transfer all of your rights under this Agreement in connection with transfer of the PRODUCT, provided you retain no copies, you transfer all of the SOFTWARE PRODUCT including all component parts, the media and printed materials, any upgrades, this Agreement, and, if applicable, the Certificate of Authenticity, and the recipient agrees to the terms of this Agreement. If the SOFTWARE PRODUCT is an upgrade, any transfer must include all prior versions of the SOFTWARE PRODUCT. However, if the SOFTWARE PRODUCT is marked Not for Resale or NFR, you may not resell it or otherwise transfer it for value 6. WARRANTY AND WARRANTY EXCLUSIONS IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES, TERMS, OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, SATISFACTORY QUALITY, CORRESPONDENCE WITH DESCRIPTION, AND NON-INFRINGEMENT, ALL OF WHICH ARE EXPRESSLY DISCLAIMED. POLYCOM NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE OR USE OF THE SOFTWARE PRODUCT. NO ADVICE OR INFORMATION, WHETHER ORAL OR WRITTEN, OBTAINED BY YOU FROM POLYCOM OR THROUGH OR FROM THE SOFTWARE PRODUCT SHALL CREATE ANY WARRANTY NOT EXPRESSLY STATED IN THIS AGREEMENT 11. MISCELLANEOUS Polycom, Inc. 2005. ALL RIGHTS RESERVED 2 above provided that you also do one of the following the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange or conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this NO WARRANTY 1 Intel Telco/Industrial Grade Server TIGPR2U Product Guide Compliance and Compatibility1Regulatory Notices Regulatory NoticesRegulatory Notices User Guide V2IU 6400-S Converged Network Appliance