Manuals / Premio Computer / Kitchen Appliance / Kitchen Entertainment Center

Premio Computer Aries/Centella manual Parallel Port Connector, Hardware Setup, Pin Definition

Models: Aries/Centella

1 131

Download 131 pages 19.28 Kb

Page 46

Image 46

Hardware Setup

Parallel Port Connector

The mainboard provides a 25-pin female centronic connector for LPT. A parallel port is a standard printer port that supports Enhanced Parallel Port (EPP) and Extended Capabilities Parallel Port (ECP) mode.

13	1
25	14

Pin Definition

PIN	SIGNAL	DESCRIPTION
1	STROBE	Strobe
2	DATA0	Data0
3	DATA1	Data1
4	DATA2	Data2
5	DATA3	Data3
6	DATA4	Data4
7	DATA5	Data5
8	DATA6	Data6
9	DATA7	Data7
10	ACK#	Acknowledge
11	BUSY	Busy
12	PE	Paper End
13	SELECT	Select
14	AUTOFEED#	Automatic Feed
15	ERR#	Error
16	INIT#	Initialize Printer
17	SLIN#	Select In
18	GND	Ground
19	GND	Ground
20	GND	Ground
21	GND	Ground
22	GND	Ground
23	GND	Ground
24	GND	Ground
25	GND	Ground

2-11

Page 46

Image 46

Premio Computer Aries/Centella manual Parallel Port Connector, Hardware Setup, Pin Definition

Contents

Aries/Centella u s e r m a n u a lSystem Manual Disclaimers Copyrightii Premio System Manual UPGRADING ContentsGETTING STARTED GETTING HELPWarranty Policy APPENDIXiv Premio System Manual Service Under WarrantyKeyboard Getting StartedSystem Unit Mouse System UnitSetting Up 2 Premio System ManualThe power indicator lights when the system is on Switches and IndicatorsThe hard drive indicator lights when the hard drive is in use The CD-ROM drive reads information on CDsCD ROM Drive 4 Premio System ManualReset Button Floppy DriveUpgrading Opening the System Unit 6 Premio System ManualInstalling an Expansion Card Installing a Hard Drive 8 Premio System ManualGetting Help TroubleshootingMonitor Does Not Work Mouse Does Not Work Keyboard Does Not Work10 Premio System Manual System Unit Problems Hard Drive ProblemsPremio on the Internet Technical Support12 Premio System Manual Warranty Warranty PolicyAppendix Premio ProductExclusions from Limited Warranty Programs Service Under Warranty14 Premio System Manual FCC Standards Important Safety Instructions 16 Premio System ManualA. When the power cord or plug is damaged or frayed MS-6534 Micro ATX Mainboard Version G52-MA00417 MICRO-STAR INTERNATIONALMicro-Star International MS-6534 Tested to comply with FCC Standard VOIR LA NOTICE DINSTALLATION AVANT DE RACCORDER AU RESEAUFCC-B Radio Frequency Interference Statement For Home or Office UseTrademarks EditionCopyright Notice Revision HistorySafety Instructions Chapter 2. Hardware Setup ContentsChapter 1. Introduction Jumpers Chapter 3. AWARD BIOS SetupEntering Setup SlotsAppendix A. Using 4-/6-channel Audio Function Chapter 4. AMI BIOS SetupGlossary Introduction1 Main Memory Mainboard SpecificationChipset SlotsH/W Audio Optional BIOSDimension S/W AudioChapter Mainboard LayoutMS-6534 Micro-ATX Mainboard IntelComponent Quick Components GuideIntroduction FunctionKey Features Hardware Setup Central Processing Unit CPU Installing the CPUOverheating will seriously damage the CPU Installing the CPU Fan LeversOverclocking CPU Core Speed Derivation Procedurethen This motherboard is designed to support overclockingMemory Introduction to SDRAMDIMM Modules Combination Installing DIMM ModulesYou can install memory modules in any combination as follows Power Supply ATX 20-Pin Power ConnectorChapter ATX 12V Power Connector JPW1JPW1 Back Panel Mouse ConnectorHardware Setup USB Connectors Keyboard Connector6-pin Female Hardware Setup Parallel Port ConnectorPin Definition Audio Port Connectors Serial Port Connectors COM A & COM BJoystick/Midi Connector FunctionConnectors Floppy Disk Drive Connector FDD1Primary IDE Connector Hard Disk Connectors IDE1 & IDE2jumper setting instructions Hardware Setup Case Connectors FP1 & FP22-15 Power LED FP1 Power SwitchReset Switch 2-pin/3-pin dual color power LED 2-pin LED is connected to pinDescription Power LED FP2LEDStatus LEDStatusSpeaker FP1 only HDD LEDKeylock FP1 only JGS1 Power Saving Switch Connector JGS1Wake On LAN Connector JWOL1 JWOL1Note Modem wake-up signal is active “low” Wake On Ring Connector JMDM1 OptionalChapter Hardware Setup IrDA Infrared Module Connectors IR1 & IR2Connectivity Design Guide Fan Power Connectors CFAN1/SFAN1 1. Always consult the vendor for proper CPU cooling fanCDIN1 connector is for CD-ROM audio connector CD-In/Aux Line-In/Modem-In Connector CDIN1/AUXIN1/ MDMIN1Hardware Setup USB Front Panel Connectors USB1 & USB2 ChapterHardware Setup Front Panel Audio Connector JAUDIO1Panel I/O Connectivity Design Guide Jumpers Clear CMOS Jumper JBAT1PCI Slots SlotsAGP Accelerated Graphics Port Slot CNR Communication Network Riser SlotAGP & PCI Slot 1 shared PCI Slot 2 & AC97 shared PCI Interrupt Request Routing2-28 AWARD BIOS Setup AWARD BIOS SetupControl Keys Entering SetupHit DEL if you want to run SETUP Sub-Menu Getting HelpMainMenu General Help F1Advanced BIOS Features The Main MenuStandard CMOS Features Advanced Chipset FeaturesLoad Optimized Defaults PnP/PCI ConfigurationsLoad Fail-Safe Defaults Set Supervisor Passwordmonth Standard CMOS FeaturesDate dateDrive A/B VideoNo Errors All ErrorsThe system stops when any error is detected The system doesn’t stop for any detected errorAnti-Virus Protection Advanced BIOS FeaturesCPU L1 & L2 Cache The system will boot from floppy drive Quick Boot1st/2nd/3rd Boot Device The system will boot from LS-120 driveSetup Typematic Rate SettingTypematic Delay Msec The password prompt appears only when end users try toPage Configure SDRAM Timing Advanced Chipset FeaturesNote Change these settings only if you are familiar with the chipset Precharge DelayDelayed Transaction RAS# to CAS# DelayEnabled and Disabled RAS# PrechargeAWARD BIOS Setup Integrated Peripherals↑↓→← IDEPrimary/SecondaryMaster/SlaveUDMA On-ChipPrimary/SecondaryPCIIDEIDE Primary/Secondary Master/Slave PIO USB ControllerIDEHDDBlockMode IR Transmission DelayOnboard/CNR LAN selection FloppyControllerIR Pin Select abled and DisabledIRDuplexMode Parallel PortIPCAFunction Power Management SetupACPIStandbyState Power Off PowerManagement/APMPower Button Function The power button functions as a normal power-onTimehhmmssAlarm Resume By RTC AlarmDateofMonthAlarm POWERONFunctionPower Again Hot Key Power ONSleep State LED Reset Configuration Data PnP/PCI ConfigurationsPNP OS Installed Resources Controlled ByIRQ Resources PCI/VGA Palette SnoopPC Health Status CPU Critical TemperatureAuto Detect PCI Clock Frequency/Voltage ControlCPU Ratio Selection SpreadSpectrumAWARD BIOS Setup Load Fail-Safe/Optimized Defaults Load Optimized Defaults When you select Load Optimized Defaults, a message as below appearsAWARD BIOS Setup ↑ ↓ → ←Set Supervisor/User Password 3-30About Supervisor Password & User Password Save & Exit Setup Exit Without Saving AMI BIOS Setup AMI BIOS SetupDELSetup Selecting the First Boot DeviceEntering Setup F11Boot MenuAMI BIOS Setup Control KeysMainMenu Default SettingsGetting Help General Help F1Chipset Features Setup Standard CMOS SetupBIOS Features Setup Power Management SetupLoad Optimal Defaults PNP/PCI ConfigurationHardware Monitor Setup Load Fail Safe Defaultsmonth Standard CMOS SetupDate datePri Master/Pri Slave/Sec Master/Sec Slave Boot Sector Virus ProtectionFloppyDriveA/B 1st/2nd/3rd Boot Device BIOS Features SetupQuick Boot The system will boot from the first HDDThe system will boot from the Network drive The system will boot from the CD-ROMThe system will boot from the SCSI The system will boot from the first BBS BIOS BootSystem BIOS Cacheable Password CheckBoot OS/2 for DRAM 64MB SwapFloppyConfigure DRAM Timing by Chipset Features SetupNote Change these settings only if you are familiar with the chipset CAS# LatencyDelayed Transaction RAS# to CAS# DelayPrecharge Delay DRAMIntegrityModeIPCAFunction Power Management SetupACPIStandbyState Mouse Wakeup From S3 PowerManagement/APMUSB Wakeup From S3 Keyboard Wakeup From S3RTCAlarm Date/Hour/Minute/Second Power Button FunctionResume By RTC Alarm Monitor and IgnoreNote If you change these settings, you must reboot the system until it enters the operating system and then power off the system. By doing so, the changed settings will come into effect next time you power on the system Power AgainClear ESCD PNP/PCI ConfigurationPCI VGA Palette Snoop DMA Channel 0/1/3/5/6/7 IRQ 3/4/5/7/9/10/11USB Legacy Support Integrated PeripheralsUSB Controller On-ChipIDEFloppyController AC’97 AudioAC’97Modem OptionParallel Port Mode IR Pin SelectParallel Port EPP Version9, 10 and AMI BIOS SetupOnBoardGamePort CPU FSB Clock Mhz Hardware Monitor SetupCPU Ratio Selection SpreadSpectrumChassis Intrusion Optional DefaultsY/N? N Load Optimal/Fail Safe DefaultsLoad Optimal Load Fail Safe DefaultsY/N? N AMI BIOS SetupLOAD FAIL SAFE DEFAULTS supervisor password Supervisor/User PasswordEnter new Additionally, when a password is enabled, you can also have AMIBIOS to request a password each time the system is booted. This would prevent unauthorized use of your computer. The setting to determine when the pass- word prompt is required is the PASSWORD CHECK option of the BIOS FEA- TURES SETUP menu. If the PASSWORD CHECK option is set to Always, the password is required both at boot and at entry to Setup. If set to Setup, password prompt only occurs when you try to enter Setup About Supervisor Password & User PasswordIDE HDD AUTO Detection ChapterSAVE & EXIT SETUP Save & Exit SetupSAVE to CMOS and EXITY/N? Y savingY/N? N Exit Without SavingQuit without EXIT WITHOUT SAVINGUsing 4-/6-channel Audio Function A Using 4-/6-channel Audio FunctionTo install C-Media drivers Installing C-Media DriversHardware Configuration 2. Click on C-Media Sound DriversTo set the multi-channel configuration Software ConfigurationClick here