Fan Power Connectors CFAN1/SFAN1 | Premio Computer Aries/Centella

Chapter 2

Fan Power Connectors: C_FAN1/S_FAN1

The C_FAN1 (processor fan) and S_FAN1 (system fan) support system cooling fan with +12V. It supports three-pin head connector. When connecting the wire to the connectors, always take note that the red wire is the positive and should be connected to the +12V, the black wire is Ground and should be connected to GND. If the mainboard has a System Hardware Monitor chipset on-board, you must use a specially designed fan with speed sensor to take advantage of the CPU fan control.

SENSOR +12V GND

C_FAN1

SENSOR +12V GND

S_FAN1

Note:

1. Always consult the vendor for proper CPU cooling fan.

2.CPU Fan supports the fan control. You can install the PC Alert utility that will automatically control the CPU Fan speed according to the actual CPU temperature.

2-22

Image 57

Premio Computer Aries/Centella manual Fan Power Connectors CFAN1/SFAN1

Contents

Aries/Centella System Manual Copyright DisclaimersIi Premio System Manual Contents Iv Premio System Manual Appendix Getting Started Premio System Manual Setting Up CD-ROM drive reads information on CDs Switches and Indicators Reset Button CD ROM Drive Upgrading Opening the System Unit Installing an Expansion Card Installing a Hard Drive Monitor Does Not Work Troubleshooting Mouse Does Not Work Keyboard Does Not Work Hard Drive Problems System Unit Problems Premio on the Internet Technical Support Appendix Warranty Policy Exclusions from Limited Warranty Programs Service Under Warranty FCC Standards Important Safety Instructions Appendix MSI FCC-B Radio Frequency Interference Statement Voir LA Notice Dinstallation Avant DE Raccorder AU Reseau Revision Revision History Date First Release August Copyright Notice Safety Instructions Contents MDMIN1 Vii Introduction1 CPU Mainboard Specification Bios Chipset Mainboard Layout Component Function Reference Quick Components Guide Key Features Hardware Setup Central Processing Unit CPU Installing the CPU Installing the CPU Fan Then CPU Core Speed Derivation Procedure Introduction to Sdram Memory Dimm Modules Combination Installing Dimm Modules ATX 20-Pin Power Connector Power Supply ATX 12V Power Connector JPW1 Back Panel Mouse Connector USB Connectors Keyboard Connector Pin Definition Parallel Port Connector Serial Port Connectors COM a & COM B Joystick/Midi ConnectorAudio Port Connectors Floppy Disk Drive Connector FDD1 Connectors Primary IDE Connector Hard Disk Connectors IDE1 & IDE2 FP2 Case Connectors FP1 & FP2 LEDStatus Description Pin/3-pin dual color power LED 2-pin LED is connected to pin Power LED FP2 HDD LED Wake On LAN Connector JWOL1 Power Saving Switch Connector JGS1 Wake On Ring Connector JMDM1 Optional Connectivity Design Guide IrDA Infrared Module Connectors IR1 & IR2 Fan Power Connectors CFAN1/SFAN1 CD-In/Aux Line-In/Modem-In Connector CDIN1/AUXIN1/ MDMIN1 USB2 USB1 USB Front Panel Connectors USB1 & USB2 Panel I/O Connectivity Design Guide Front Panel Audio Connector JAUDIO1 Clear Cmos Jumper JBAT1 Jumpers AGP Accelerated Graphics Port Slot SlotsPCI Slots CNR Communication Network Riser Slot PCI Interrupt Request Routing Award Bios Setup Control Keys Entering Setup MainMenu Getting HelpSub-Menu General Help F1 Main Menu Load Fail-Safe Defaults PnP/PCI ConfigurationsLoad Optimized Defaults Set Supervisor Password Day Standard Cmos FeaturesMonth Year Video Drive A/B HaltOn Advanced Bios Features Anti-Virus ProtectionCPU L1 & L2 Cache 1st/2nd/3rd Boot Device Quick BootBoot Other Device BootUpNum-LockLED Typematic Delay Msec Typematic Rate SettingGate A20 Option Typematic Rate Chars/SecPage Configure Sdram Timing Advanced Chipset FeaturesPrecharge Delay CAS# Latency Delayed Transaction RAS# to CAS# DelayRAS# Precharge DRAMDataIntegrityMode AGP Integrated Peripherals IDE Primary/Secondary Master/Slave PIO On-ChipPrimary/SecondaryPCIIDEIDEPrimary/SecondaryMaster/SlaveUDMA USB Controller IR Transmission Delay Serial Port B ModeOnboard/CNR LAN selection IDEHDDBlockMode IRDuplexMode Parallel Port ModeIR Pin Select Parallel Port Power Management Setup IPCAFunctionACPIStandbyState Power Button Function PowerManagement/APMMODEMUseIRQ Suspend Time Out DateofMonthAlarm Resume By RTC AlarmTimehhmmssAlarm POWERONFunction Hot Key Power on Power AgainSleep State LED PNP OS Installed PnP/PCI ConfigurationsReset Configuration Data Resources Controlled By PCI/VGA Palette Snoop IRQ Resources PC Health Status CPU Critical Temperature CPU Ratio Selection Frequency/Voltage ControlAuto Detect PCI Clock SpreadSpectrum Award Bios Setup Load Fail-Safe Defaults Load Fail-Safe/Optimized Defaults Load Optimized Defaults Set Supervisor Password Set Supervisor/User Password About Supervisor Password & User Password Save & Exit Setup Exit Without Saving AMI Bios Setup Select First Boot Device Selecting the First Boot Device Load Bios Setup defaults Default Settings Standard Cmos Setup Bios Features SetupChipset Features Setup Hardware Monitor Setup PNP/PCI ConfigurationLoad Optimal Defaults Load Fail Safe Defaults Amibios Setup Standard Cmos Setup Standard Cmos Setup Boot Sector Virus Protection Pri Master/Pri Slave/Sec Master/Sec SlaveFloppyDriveA/B Amibios Setup Bios Features Setup Bios Features Setup BootUpNum-Lock Try Other Boot DevicesFull Screen Logo Show A.R.T. for Hard Disks Boot OS/2 for Dram 64MB Password CheckSystem Bios Cacheable Option Description Configure Dram Timing by Chipset Features Setup AGP Aperture Size DRAMIntegrityMode S1/POS Mouse Wakeup From S3 USB Wakeup From S3Keyboard Wakeup From S3 Specific Key for Wakeup Wake Up On Ring/LAN/PME RTCAlarm Date/Hour/Minute/Second Power Again PNP/PCI Configuration Clear EscdPCI VGA Palette Snoop IRQ 3/4/5/7/9/10/11 DMA Channel 0/1/3/5/6/7 USB Legacy Support On-ChipIDEOnboardAudioChipOptional AC’97 Audio OnBoard Midi Port DMAChannel OnBoardGamePort CPU FSB Clock Mhz Hardware Monitor Setup Chassis Intrusion Optional Load Optimal Defaults Load Optimal/Fail Safe Defaults Load Fail Safe DefaultsY/N? N Enter new Supervisor password Supervisor/User Password About Supervisor Password & User Password IDE HDD Auto Detection Save to Cmos and EXITY/N? Y Quit without SavingY/N? N Using 4-/6-channel Audio Function a Hardware Configuration Installing C-Media DriversTo install C-Media drivers Click on C-Media Sound Drivers To set the multi-channel configuration Software Configuration