Operation, Switch on procedure | Procom EVS200 manual

VOR/ILS Analyzer EVS200

Chapter 3: Operation

Operation

Switch On/switch Off the unit at mains supply

With the mains switch at the rearside switch the unit on or off.

With the switch "POWER" at the front side switch the unit on or "STANDBY".

On switch position "STANDBY" the in- stalled battery (option) will be charged. Details see item "Battery Operation"

(page 12).

Switch On/switch Off the unit at VDC supply

When the unit is supplied from the installed battery (option) or through the external DC input it must be switched on or to "STANDBY" only with the Switch "POWER" at the frontside.

On external DC supply of the unit the installed battery

(option) will not be charged!

Switch on procedure

During the switch on procedure the VOR/ILS Analyzer EVS200 performs a selftest (BITE). The tested functions are indicated with "OK". This test takes approx. 5 s. After that automatically it is switched over to the startup mode which was set in the setup.

Because of the displayed battery voltage

(U BATT) it is possible to value the charging state of the installed battery (option).

Malfunctions of the BITE will be indicated by "FAIL". In that case the unit does not switch over to the startup mode (see also item "Selftest").

0796.1800.02

E-8

11

Image 20

Procom EVS200 Operation, Switch On/switch Off the unit at mains supply, Switch On/switch Off the unit at VDC supply

Contents

VOR/ILS Analyzer EVS200 VOR/ILS Analyzer EVS200 Issue Version E8 0201 EVS200796.1800.02 Rohde & Schwarz GmbH & Co. KGPage Safety Instructions Safety Instructions Contents Operator InformationPreparation for Operation Operation Interfaces RS-232-Interface operation Service Technical SpecificationService Warranty Technical data General data Accessories Important operator information Operator Information Unpacking Unpack the VOR/ILS Analyzer EVS200 Application of the unit Characteristics of the unit Unit layout frontview Unit layout rearview Safety Rules Placing the unitPreparation for Operation Mains connection Cable specification FO cable jack Assembling the FO Cable Jack RS-232-Interface Antenna connectionAF OUT Setup Preparation for Operation External AF inputDSP output ILS-Mode VOR-Mode Display Switch On/switch Off the unit at mains supply Switch On/switch Off the unit at VDC supplySwitch on procedure Operation Battery operation Operation Selftest Bite Displ 2/2 SETUP-Mode Parameter Description Setting value Operation Operating instructions of SETUP-Mode ILS-Mode Operating instructions of ILS-Mode Operation Operating instructions of Y /t setup menu Operation Operating instructions of Store DDM menu Operation Signal parameters on ILS display Displ 1/2Displ 2/2 Store VOR-Mode Operating instructions of VOR-Mode Signal parameters on VOR display BEACON-Mode Operating instructions of BEACON-Mode Signal parameters on Beacon display Display indication Description Measuring value Level-Mode Operating instructions of Δ Level-Mode Operation Storing and recalling reference levels VOR/ILS Analyzer EVS200 Signal parameters on Δ Level Display Spectrum-Mode Operating instructions of Spectrum-Mode Control commands RS-232-Interface operationCOM-Parameter Handshake Unit related control commands Command RF frequency in kHz FunctionCommand LO Function Command EC0 Function Command EC1 Function Command test FunctionCommand LA Function EC1 Command RES Function Command BI FunctionRES Reset Rescr Ready CR/LF Command VER Function Command ML FunctionCommand MV Function ML Mode-Delta Level Level mode setting Mode related control commands ILS-Mode Command MI FunctionCommand MB Function Command DD0 Function Command DD1 Function Command SD0 FunctionCommand SD1 Function DD1 Command AM2 Function Command AM3 FunctionCommand PH Function Phase 90/150 Hz Query of Phase angle 90/150 Hz Command BW0 Function Command BW1 FunctionBW0 bandwidth information KHz bandwidth setting BW1 bandwidth information KHz bandwidth setting Command FA1 Function OFF Command FA2 Function Modulation depth Command FA3 Function AM90 CR , AM 150 CRExample CR DDM CR RF level Command FA0 Function Command D1 FunctionCommand D2 Function D1 display information Switch over to display1 Command AF8 Function Command AM8 FunctionCommand AM9 Function AF8 AF-frequency ID AF-frequency ID query Command be Funcion Command AM0 FunctionCommand AM1 Function VOR-Mode Command FM0 Function Command FM1 FunctionFM0 FM1 D2 Display-information Switching over to Display2 FM-Index FA2 Fast measuring on Activating the Fast measurement modeFM-deviation FA3 Fast measuring on Activating the Fast measurement mode Example Command from the controller Input e.g. a Command SR Function Command LR FunctionCommand LD Function Level-Mode Command AM4 Function Command AM5 FunctionCommand AM6 Function Beacon-Mode Command AF5 Function Command AM7 Kommando FunktionCommand AF4 Function Command AF6 Function Command AF7 FunktionAF6 AF7 Interfaces Interfaces External AF input Labeling Description RS-232-Interface Labeling DescriptionExternal VDC connection Mains connection Labeling Description Service Receiver section Technical dataILS signal analysis VOR signal analysis Temperature range Dimensions and WeightEMC Order notification Accessories Description Ident No