Operation of the unit, Displ 2/2 | Procom EVS200 specification

VOR/ILS Analyzer EVS200

Chapter 3: Operation

Operation of the unit

Because of the many universal measuring functions of the VOR/ILS Analyzer EVS200 the operation has to be carried out according to the following instructions. Basically all measurement parameter set- tings are realized through softkeys and the mode keys. An activated mode is shown by a luminous LED (beside the belonging mode key). All important signal parameters are analyzed by the DSP (digital signal processor) and indicated on the display. Due to the variety of the analyzed parameters the indi- cation in the ILS and VOR mode is subdivided into two display parts ("DISPL 1/2" and

DISPL 2/2").

The RS-232-Interface operation of the VOR/ILS Analyzer EVS200 is described in section "Operating the VOR/ILS ANALYZER EVS200 via RS-232-Interface"

General operating instructions of the VOR/ILS Analyzer EVS200

0796.1800.02

E-8

Page 22

Image 22

Procom EVS200 user manual Operation of the unit, Displ 2/2

Contents

VOR/ILS Analyzer EVS200 VOR/ILS Analyzer EVS200 Issue Version E8 796.1800.02 0201EVS200 Rohde & Schwarz GmbH & Co. KGPage Safety Instructions Safety Instructions Preparation for Operation ContentsOperator Information Operation Interfaces RS-232-Interface operation Service Warranty ServiceTechnical Specification Technical data General data Accessories Important operator information Operator Information Unpacking Unpack the VOR/ILS Analyzer EVS200 Application of the unit Characteristics of the unit Unit layout frontview Unit layout rearview Preparation for Operation Safety RulesPlacing the unit Mains connection Cable specification FO cable jack Assembling the FO Cable Jack AF OUT Antenna connectionRS-232-Interface DSP output SetupPreparation for Operation External AF input ILS-Mode VOR-Mode Display Switch on procedure Switch On/switch Off the unit at mains supplySwitch On/switch Off the unit at VDC supply Operation Battery operation Operation Selftest Bite Displ 2/2 SETUP-Mode Parameter Description Setting value Operation Operating instructions of SETUP-Mode ILS-Mode Operating instructions of ILS-Mode Operation Operating instructions of Y /t setup menu Operation Operating instructions of Store DDM menu Operation Displ 2/2 Signal parameters on ILS displayDispl 1/2 Store VOR-Mode Operating instructions of VOR-Mode Signal parameters on VOR display BEACON-Mode Operating instructions of BEACON-Mode Signal parameters on Beacon display Display indication Description Measuring value Level-Mode Operating instructions of Δ Level-Mode Operation Storing and recalling reference levels VOR/ILS Analyzer EVS200 Signal parameters on Δ Level Display Spectrum-Mode Operating instructions of Spectrum-Mode COM-Parameter Control commandsRS-232-Interface operation Handshake Command LO Function Unit related control commandsCommand RF frequency in kHz Function Command EC0 Function Command LA Function Command EC1 FunctionCommand test Function EC1 RES Reset Command RES FunctionCommand BI Function Rescr Ready CR/LF Command MV Function Command VER FunctionCommand ML Function ML Mode-Delta Level Level mode setting Command MB Function Mode related control commands ILS-ModeCommand MI Function Command DD0 Function Command SD1 Function Command DD1 FunctionCommand SD0 Function DD1 Command PH Function Command AM2 FunctionCommand AM3 Function Phase 90/150 Hz Query of Phase angle 90/150 Hz BW0 bandwidth information KHz bandwidth setting Command BW0 FunctionCommand BW1 Function BW1 bandwidth information KHz bandwidth setting Command FA1 Function OFF Command FA2 Function Modulation depth Example CR DDM Command FA3 FunctionAM90 CR , AM 150 CR CR RF level Command D2 Function Command FA0 FunctionCommand D1 Function D1 display information Switch over to display1 Command AM9 Function Command AF8 FunctionCommand AM8 Function AF8 AF-frequency ID AF-frequency ID query Command AM1 Function Command be FuncionCommand AM0 Function VOR-Mode FM0 Command FM0 FunctionCommand FM1 Function FM1 D2 Display-information Switching over to Display2 FM-deviation FA2 Fast measuring on Activating the Fast measurement modeFM-Index FA3 Fast measuring on Activating the Fast measurement mode Example Command from the controller Input e.g. a Command LD Function Command SR FunctionCommand LR Function Level-Mode Command AM6 Function Command AM4 FunctionCommand AM5 Function Beacon-Mode Command AF4 Function Command AM7 Kommando FunktionCommand AF5 Function AF6 Command AF6 FunctionCommand AF7 Funktion AF7 Interfaces External VDC connection Interfaces External AF input Labeling DescriptionRS-232-Interface Labeling Description Mains connection Labeling Description Service ILS signal analysis Technical dataReceiver section VOR signal analysis EMC Temperature rangeDimensions and Weight Order notification Accessories Description Ident No