11. TERMINAL STRIP DETAILS |
| Tab. 9 | |||
| Terminal | Description |
| Technical | Indications |
| strip |
|
| specifications |
|
| reference |
|
|
|
|
|
|
|
|
|
|
| M3 | Main supply |
| 120 VAC – 60 Hz | The main supply cable must be anchored to the |
|
|
|
|
| boiler frame (Fig. 39) and pass through the |
35) |
|
|
|
| strains relief (field supplied). Cable as specified in |
|
|
|
| the electrical supply. | |
(Fig. |
|
|
|
| |
|
|
|
|
| |
M3a |
|
|
| ||
voltage |
|
| The | ||
| Connections for DHW |
|
| ||
|
|
|
| Model: Honeywell VC6011 (actuator) + VCZMK6000 | |
|
| external |
| 120 VAC – 60 Hz | (Cartridge valve) |
High |
|
|
|
| frame (Fig. 39) and pass through the strains relief (field |
|
|
|
| supplied) (Fig. 39). Cable as specified in the electrical | |
|
|
|
|
| supply. |
| M4 | Outdoor sensor |
| 12 K Ohm B3760 |
|
| M4 | Remote control |
| Open therm plus protocol | Only Raypak Part No. 013073 |
|
|
|
|
|
|
| M4a | Room thermostat |
| 24 VDC | Volt free (Jumper when not used) |
|
|
|
|
|
|
| M4a | Tank sensor |
| 10 K Ohm B3435 | Immersion type. |
35) |
| for DHW |
|
| If the boiler is installed with a tank sensor, the Jumper |
|
|
|
| on the PCB must be in position 2 (Fig. 61) | |
(Fig. |
|
|
|
| |
M2a | Tank thermostat |
| On/off (NO) | Volt free | |
voltage |
| ||||
| for DHW |
|
| If the boiler is installed with a tank termostat, the | |
|
|
|
|
| Jumper on the PCB must be in position 3 (Fig. 61) |
Low | M3b |
| On/off (NC) | Volt free. | |
| thermostat and condensate |
|
| This is a generic input to lock out the boiler. Jumper when | |
|
|
|
|
| (generic available alarm) not used). If the contact will be |
|
|
|
|
| open the alarm number 21 |
|
|
|
|
| will appear on the display and the boiler is lock out |
|
|
|
|
|
|
REMOTE CONTROL |
| LOW VOLTAGE | CONDENSATE PUMP ALARM | ||||
EXTERNAL |
|
|
| UNDERFLOOR HEATING LIMIT | |||
| SENSOR |
|
|
|
| THERMOSTAT OR | |
0T+ |
|
|
|
|
| (jumper when not used) | |
|
|
|
|
|
| ||
|
| ROOM |
|
|
|
| |
|
|
|
|
|
|
| |
|
|
| THERMOSTAT | TANK |
|
| |
|
|
|
|
| |||
|
| TANK | (jumper when |
|
| ||
|
| THERMOSTAT | not used) | SENSOR |
| M3b |
M4 | |
| |
| V |
| M2 |
| M4a |
HIGH VOLTAGE
3W |
|
|
|
|
| 120V | |
| (COMMON)BLUE | (CLOSED)BROWN | BLACK(OPEN) |
|
|
| |
|
| N |
| L | |||
|
|
|
|
|
|
| F= |
M3a |
|
|
| M3 |
| fuse 4AF | |
|
|
|
|
| |||
|
|
|
|
|
|
| |
PCB fuse=4AT |
|
|
|
|
|
| |
|
|
|
|
|
| ||
|
|
|
| Cod. 20003227 | |||
|
|
|
|
|
|
Fig. 35
36