Manuals / Samsung / Communications / Telephone

Samsung manual InstallationOfficeServ Link Version 2.1 User Guide

Models: Version 2.1

1 54

Page 15

InstallationOfficeServ Link Version 2.1 User Guide

--------------------------------------------------------------------------------------------------------------------------------------------------------------------

9.The installation program asks if you want Link to run automatically at the time of system booting. It you want, click on the [Yes] button. Then, the program will link you to the Startup folder.

10.Installation has successfully completed. Click on the [Finish] button, then the installation program exits.

Page 15

Image 15

Samsung manual InstallationOfficeServ Link Version 2.1 User Guide

Contents

Version June User GuideOfficeServ Link OfficeServ Link User GuideCOPYRIGHT TRADEMARKSPreface About This ManualConventions OfficeServ Link Version 2.1 User GuidePreface This page left blank intentionallyPage Chapter 2 Installation of Link Table of contentsPreface Table of contentsChapter 5 Link Operating State View Table Of ContentsChapter 4 Using Link Chapter 6 Message MonitoringVarious Connections to PBX systems Various Option SettingsChapter 1 Introduction Overview of OfficeServ LinkOfficeServ Link Version 2.1 User GuideIntroduction This page left blank intentionallyPage DCS Key Telephone Requirements Chapter 2 Installation of LinkPreparation for installing Link Computer System RequirementsOfficeServ Configuration EnvironmentFigure 2.1 Typical configuration diagram OpenTSPSystem Administration Requirements InstallationPage Page OfficeServ Link Version 2.1 User GuideInstallationInstallationOfficeServ Link Version 2.1 User Guide Page OfficeServ Link Version 2.1 User GuideInstallationInstallationOfficeServ Link Version 2.1 User Guide Post Installation Installing the Link LicenseChecking the registered program group Page Chapter 3 OfficeServ Link SettingsExecuting OfficeServ Link YES, the system booting runs the Link automaticallyDescription of Link Main Window Configuration of Link Main WindowFigure 3.3 Status Bar y Link Status bar informationConnection mode to telephone system Communication Environment SetupDCS 180 SIM Type, 9600 BPS Communication environment setup for SIM / Serial cable connectionsCommunication Environment Setup for TCP/IP connections Primary speed of serial communications for each telephone systemFigure 3.5 Status View of Ports in Use Communication Environment Setup for user connection in standbyExample of Environment Setup PageFigure 3.6 Example of TCP/IP connections Option Settings Normal optionRestriction for the currently connected users in number Automatic connection to PBX system at Link startup General message monitoring option settingsMessage Monitoring and Saving Option Message Auto Clear OptionFigure 3.9 General message monitoring program SMDR/ UCD message monitoring option settingsPassword Protection Option Figure 3.11 Link indicator for message monitoring setting statusSMDR / UCD Message Exteranl Send Options OfficeServ Call+ Function Support OptionLink State Message Display Option Figure 3.12 Language mode change alarm message Switch Link Recovery Try Count OptionRecovery Try Time Period Option Link Display Language OptionLink SettingsOfficeServ Link Version 2.1 User Guide This page left blank intentionallyPage Page Telephone settings for a serial Link connection Chapter 4 Using LinkCheck the configuration of the Phone System Connecting to a telephone systemConnecting PBX system after Setup of Communication Environment Figure 4.1 Click on the CONNECT buttonFigure 4.2 Process of connection to telephone system GeneralMessage.ico ErrorMessage.ico Figure 4.4 Automatic recovery message after error eventFigure 4.3 Connection success message Page Figure 4.5 1st recovery try failed and wait 1 minuteFigure 4.6 recovery success OfficeServ Link Version 2.1 User GuideMessage MonitoringDisconnecting to the PBX system and user Figure 4.7 Selection of Disconnect buttonFigure 4.8 Disconnection process in progress Chapter 5 Link Operating State View Viewing Link state in Default modeIn case that a user is currently connected Running the Switch Message Monitor SCMonitor.exe Chapter 6 Message MonitoringCall processing message monitoring program Figure 6.2 Environment Setup of Switch Message Monitor Program Environment SetupFigure 6.3 Main window of Switch Message Monitor Figure 6.4 Monitoring program showing system messages SMDR / UCD Message Monitoring ProgramFigure 6.5 Executing the SMDR / UCD Message Monitor Running the SMDR / UCD Message Monitor SUMonitor.exeEnvironment Setup Figure 6.6 Setup of SMDR / UCD Message Monitor Environmentvalues entered in the environment setup entries of Link Message Monitor program were installed inFigure 6.7 Main Window of SMDR / UCD Message Monitor Figure 6.8 Main window of SMDR / UCD Message Monitor Message MonitoringOfficeServ Link Version 2.1 User Guide Pagename Electronics\OfficeServ Link\Tools\MSGMonitor.exe” Installing Monitoring Program on other ComputerMessage MonitoringOfficeServ Link Version 2.1 User Guide This page left blank intentionallyPage Page Running the License Tools Chapter 7 License RegistrationFigure 8.3 Paste the valid license key Installing the LicenseFigure 8.5 License Registration Notification OfficeServ Link Version 2.1 User GuidePage Figure 8.4 Link Shutdown CheckFigure 8.8 How to check the License Status OfficeServ Link Version 2.1 User Guide This page left blank intentionallyPage Visit us at User GuideSamsung OfficeServ Link Information in this document is subject to change without notice