Important Note When Wiring for XM Type | Sanyo XMHX1252 manual

5-5. Important Note When Wiring for XM Type

Connect the wires referring to the diagram. Note that the remote control wires and the power supply wires are not supplied. The remote control wires shall be segregated from the power supply wires as follows:

1.Install the optional remote control wires (field supplied) and the manufacturer supplied 3-way wiring harness to the electrical connection box as shown in the diagram. One end of the optional remote control wiring is connected to the R1/R2 terminals. Then place and fix the two clasps so that the clasps shall cover both the remote control wires and the 3-way wiring harness as shown in the magnified drawing.

2.Connect the grounding conductor of the incoming power supply to the earth (ground) screw before connecting the power supply conductors to "L1, L2" of the terminal block.

3.Securely affix the two power supply conductors (L1, L2) in the wiring channel by the clamping strap as shown.

NOTE

Take care not to damage the remote wiring by the clasp. Do not leave the remote wiring loose.

XM Type

3-way connection wiring with harness (supplied)

Optional remote control wire (field supplied)

Clasp

Power wiring (field supplied)

Conduit

Earth screw

Clamping strap

Entirely cover the remote wiring and the 3-way wiring harness with the clasp.

Remote control wiring

75

W-3WAY_ECO-i_US.indd 75	2008/02/07 10:56:09

Image 75

Sanyo XMHX1252, XMHX1852, CHDZR09053, CHDZR14053, 85464369098000 Important Note When Wiring for XM Type

Contents

Optional Controllers Sanyo Commercial SolutionsR410A Models Indoor Units Outdoor Units …In an Area with High Winds For safe installation and trouble-free operation, you must…In a Room …In Moist or Uneven Locations Countermeasures Amount 353 oz Amount 529 oz Manifold gauge Vacuum pump Care regarding tubingBe sure to recharge the refrigerant only in liquid form Different tools required Refrigerating machine oil differs R22 Compressor specifications are differentSingle-outlet valve Existing tubing cannot be used especially R22 Contents Test RUN 8-1. Preparing for Test Run Electrical Wiring 5-1. General Precautions on WiringHOW to Process Tubing AIR Purging Type of Copper Tube and Insulation Material Tools Required for Installation not suppliedAccessories Supplied Outdoor Unit Part name Concealed Duct For sealing recessed portion of power supply4-Way Air Discharge Semi-Concealed X-Type 1-Way Air Discharge Semi-Concealed 4-Way Air Discharge Semi-Concealed XM Type Concealed Duct High-Static PressureCeiling-Mounted Wall-Mounted H3 C Tubing Length BTU/h 95.500 153.600 Tubing Size 10 Main Tubing Size LA11 Main Tubing Size After Distribution LB, LC 12 Outdoor Unit Tubing Connection Size a D 15 Refrigerant tubing Existing tubing can be used 17 Refrigerant Charge Amount at Shipment for outdoor unit System Limitations 18 System LimitationsCommon solenoid valve kit Header joint system Tube branching methods horizontal useHeader joint system Indoor Size Part B Part C Part D Part E Part F Part G Part H Inch Tubing size with thermal insulationModel name Cooling capacity after distribution Remarks Suction Tube Discharge Tube Liquid Tube 21 Dimensions for connections of each part Optional Solenoid Valve Kit Precautions on Installation of Solenoid Valve KitTypes and specifications Specifications Unit Relay kit Front Installation of Solenoid Valve Kit Main tubing Distribution joint tubing R410A additional charging absolutely mustBe done through liquid charging Example Use the same tools for R22 and for R410A Remark Main tubing Front view Ceiling-MountedTypeWall-Mounted Type Indoor Unit Outdoor Unit Without snow- proof ducting Without platform Precautions When Installing in Heavy Snow Areas Air direction Front direction Unit installationCeiling panel Unit Ceiling panel Air direction Placing the Unit Inside the Ceiling Suspending the Indoor Unit Installing the Drain Piping Start when you short the pin Be careful since the fan willOn the indoor control board Removing the corner cover Installing the Ceiling Panel Attaching the air-intake grille Wiring the Ceiling Panel Special Remarks DC Fan Tap Change Procedure Checking After InstallationWhen Removing the Ceiling Panel for Servicing Adjusting the Auto Flap Placing the Unit Inside the Ceiling Suspending the Indoor Unit From the drain pipe outlet Installing the Drain PipingDo not install an air bleeder as This may cause water to spray Checking the unit position How to Install the Ceiling Panel Main unitBefore Installing the Ceiling Panel Checking the Drainage Wiring the Ceiling Panel Installing the Ceiling Panel Adjusting the Auto Flap How to Attach the Corner & Air-Intake GrilleChecking After Installation When Removing the Ceiling Panel for Servicing 23-5/8 22-3/64 Be sure to use a level gauge Confirm that the unit isLevel. If it is not level, water Leakage may occur Installing the Drain Piping 3WAYECO-iUS.indd 2008/02/07 Ss12 or 5/32 ss15/32 For fastening Electrical Power Wiring Wiring connectionsWiring M5 ss40 Removing the side panel Removing the intake grille Air leakage If a wireless remote controller is used Installing the side panel and intake grilleInstalling the intake grille Others Check after installation Refrigerant tubing Inspection access27/32 Indoor unit Air outlet duct flange Ceiling. Ensure that the ceiling is strong Enough to support the weight of the unitIt is important that you use extreme care Supporting the indoor unit inside Section directly after the connection port can be raised a Maximum of 19-11/16. Do not raise it any higher than19-11/16, as this could result in water leaks. Fig Increasing the Fan Speed How to read the diagramBe careful since the fan will start when you Short the pin on the indoor control board 17-23/32 23-5/8 for checking and servicing the electrical system 31/32 Min -31/32 Inspection plug Indoor Fan Performance How to Read the Diagram Refrigerant tubing drain hose position Indoor unit from the ceil Wall and ceiling side opening positionIt is important that you use Extreme care in supporting Approx 63/64 Ceiling Surface Washer Nut Fixture Double nut Field supply Downward gradient Min /100 Duct for Fresh AirShaping the Tubing Rear cover Ing. Also, check any specified How to carry out power supply wiringCheck local electrical codes Regulations before wir Installing the Rear Panel onto the Wall Selecting and Making a HoleIf the Wall is Wooden Attaching the grille Removing the Grille to Install the Indoor UnitIf the Wall is Brick, Concrete or Similar Removing the grille Left or left-rear tubing Installing the Drain HoseDo not supply power to the unit or operate Shaping the Tubing Right-rear tubing KHX2452 KHX0752 / 0952 / 1252 Installing the Outdoor Unit Positions where anchor bolts are fastenedTransporting Routing the Tubing Remove the Brackets Used for Transport Tubing size mm Outer dia Thickness Prepare the TubingConnect the Tubing Refrigerant tube port Work method Tightening torque for each cap Use shielded wiring General Precautions on WiringOutdoor unit Time delay fuse or Circuit capacity Inter-outdoor unit control wiring For K, A, X, T, U and D Types Wiring System DiagramPower Wiring Controller XM Type For XM Type Outdoor unit Indoor unit How to connect wiring to the terminal For stranded wiring Type Important Note When Wiring for Common Type Type XM Type Important Note When Wiring for XM Type Deburring Connecting the Refrigerant TubingFlaring Procedure with a Flare Tool Use of the Flaring Method Approximate Tube diameter Tightening torque Two tubes arranged together Three tubes arranged togetherFour tubes arranged together Taping the Tubes Finishing the Installation Air Purging with a Vacuum Pump for Test Run Preparation Leak testManifold gauge Vacuum pump 45 min. or more 90 min. or more Evacuation Charging additional refrigerant Use a cylinder designed for use with R410AFinishing the job Test RUN Test Run Procedure Items to Check Before the Test RunUnit with the unit Address setting of main outdoor unit S007 Unit No. setting Indoor unit setting S004 Rotary switch, red Main Outdoor Unit PCB Setting Outdoor main/sub Auto Address Setting Basic wiring diagram ExampleAutomatic Address Setting from the Outdoor Unit No main unit Settings 22-9 Automatic Address Setting no compressor operation Automatic Address Setting from Outdoor Unit3 OFF Automatic Address Setting in Heating Mode Automatic Address Setting* from the Remote Controller Automatic Address Setting in Cooling Mode Display during automatic address setting LED 2Blink alternately If 1 indoor unit is connected to 1 remote controller Remote Controller Test Run SettingsChecking the indoor unit addresses LED Possible cause of malfunction Message Alarm messages displayed on system controller Way Air Discharge Semi-Concealed Type X, XM Types Should the power fail while the unit is running Tips for Energy SavingSoot Way air discharge semi-concealed type a Type 1-WAY 100 Troubleshooting 101 Concealed Duct High-Static Pressure Type U, D TypesType standard static pressure Type high static pressure 102 On the wired remote control unit 103 CEILING-MOUNTED 104 Or soot 105 106 Tips for Energy Saving