[C1] Setting the Input Configuration (SET UP 1) — INPUT CONFIGURATION Menu

Menu 2 Chapter

Notes

•Even when selecting AUTO, also select NTSC (SETUP 7.5 or 0), PAL (S or D), and PAL-M (S or D).

•If there is no input connector or decoder corresponding to a format, that format will not be selectable (the cursor will skip over that entry).

•If you change the format of the channel to which the SDI signal is assigned to AUTO of the COMPOSITE menu with the BKM-21D installed, the image may not be displayed. In this case, change the signal format to NTSC or PAL once, then reset it to AUTO.

•If you change the format of the PAL-M Y/C signal to AUTO of the YC menu with the BKM-26M installed, the image may not be displayed. In this case, select PAL-M S or D.

[C112] COMPONENT menu

Select the component signal format, or RGB.

YPBPR SMPTE/EBU-N10

YPBPR BETACAM: SETUP 7.5 or 0.

RGB

[C113] SDI menu

Select the format of the serial digital signal 1). NTSC: SETUP 7.5 or 0.

PAL: S (simple) or D (delay)

4:2:2

AUTO: The NTSC, PAL or 4:2:2 format of the input signal is detected and switched automatically. 1)

1)• It will take a few seconds to detect the format of an input signal when AUTO is selected. It is recommended that a particular format be selected if it is determined.

•If the serial digital signal is not properly displayed in SDI AUTO mode, re-enter the channel number.

[C14] SAFE AREA MODE menu

Set the safe area display modes. SIZE: Select the safe area mode.

16:9-80%:Displays a 80% safe area with 16:9 aspect ratio.

16:9-88%:Displays a 88% safe area with 16:9 aspect ratio.

16:9-90%:Displays a 90% safe area with 16:9 aspect ratio.

16:9-93%:Displays a 93% safe area with 16:9 aspect ratio.

16:9-ANY SIZE: Displays a safe area with 16:9 aspect ratio in the size determined by H SIZE and V SIZE.

4:3-80%:Displays a 80% safe area with 4:3 aspect ratio.

4:3-88%:Displays a 88% safe area with 4:3 aspect ratio.

4:3-90%:Displays a 90% safe area with 4:3 aspect ratio.

4:3-ANY SIZE: Displays a safe area with 4:3 aspect ratio in the size determined by H SIZE and V SIZE.

H SIZE: When 16:9-ANY SIZE or 4:3-ANY SIZE is selected, adjust the horizontal size of the safe area in 1% steps.

V SIZE: When16:9-ANY SIZE or 4:3-ANY SIZE is selected, adjust the vertical size of the safe area in 1% steps.

H POSITION: Adjust the horizontal display position of the safe area (–32 to +32).

SHAPE: Select the shape of the SAFE AREA MARKER.

SHAPE A:

HD SDI

[C12] YC SEP menu Select a Y/C separation filter. TRAP/BPF: Select TRAP/BPF filter.

2 LINES COMB: Select 2 LINES COMB filter.

3 LINES COMB: Select 3 LINES COMB filter.

[C13] SCREEN MODE menu Select the scan size.

16:9-NORM:Overscanned 16:9 aspect ratio.

16:9-UNDR:Underscanned 16:9 aspect ratio.

4:3-NORM:Overscanned 4:3 aspect ratio.

4:3-UNDR:Underscanned 4:3 aspect ratio.

SHAPE B:

4:3 AREA MARKER: Select whether the 4:3 line is displayed in16:9 screen or not (ON or OFF).

4:3 BLANKING: Select the blanking outside the 4:3 area.

HALF: Half blanking

BLACK: Blanks outside the 4:3 area.

OFF: Do not blank.

38