[C4] Setting the Channel Selection Method, Power-Up Conditions and Decoder (SET UP 4) — SYSTEM CONFIGURATION Menu

Menu 2 Chapter

Overview

The SYSTEM CONFIGURATION menu is used for the following settings:

•Channel number entry method (INPUT SELECT menu)

This menu sets the way in which the numeric keypad can be used to enter channel numbers.

•Power-up condition (STANDBY MODE menu)

This menu sets the condition of the monitor when the MAIN POWER switch on the rear panel is switched on.

•Power-up input channel (DEFAULT CH menu)

This menu sets the power-up input channel.

•Time from power-up until degauss (DEGAUSS

DELAY menu)

If several monitors are turned on at the same time and all start degaussing at the same time, there will be a very large current draw on the power supply for a few moments. To prevent this, the delay time between power-up and degaussing can be set for each monitor independently.

•Residual subcarrier detection (RESIDUAL SC SW menu) (when using the BKM-24N/25P)

It is possible to detect residual subcarrier signals from phase change by setting the decoder adpator’s residual subcarrier switch on.

•Auto color control (ACC SW menu) (when using the BKM-27T)

Selects if the ACC (Auto Color Control) circuit is activated or deactivated.

•Setting of the contrast and brightness after adjusting the white balance (CONT/BRT HOLD menu)

Selects if the adjusted contrast and brightness are retained or they are reset to the center values.

•Assigning shortcut to the COLOR TEMP ADJ menu to the [F2] key (COL TEMP SHORT-CUT menu)

Assigns the shortcut to the MANUAL menu of the COLOR TEMP ADJ menu to the [F2] key. This allows you to jump directly to the MANUAL menu corresponding to the color temperature set to the currently displayed image (STD/COL 1/COL 2/CH SET).

Structure of the SYSTEM CONFIGURATION Menu

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Level 1

 

 

 

 

Level 2

 

 

 

 

 

 

 

 

 

 

INPUT CONFIGURATION C1

 

 

 

 

 

 

 

REMOTE C2

 

 

 

 

 

 

 

PASSWORD C3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INPUT SELECT

 

 

SYSTEM CONFIGURATION

C4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

STANDBY MODE

 

 

ON SCREEN SET

C5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DEFAULT CH

 

 

ALIGNMENT

C6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DEGAUSS DELAY

 

 

WHITE UNIFORMITY

C7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RESIDUAL SC SW

 

 

EXTEND MENU

C8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ACC SW

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CONT/BRT HOLD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

COL TEMP SHORT-CUT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

44