Cueing up to shot marks adjacent to the current tape position (index function)

1In item G01 of the shot mark operation menu (page 6-2), select one of recording start mark, shot mark 1, shot mark 2, and post mark, or select all.

2Holding down the MARK button, press the F FWD button or REW button.

While the tape is moving the F FWD button or REW button flashes.

When the shot mark is detected, its type is displayed in time data display area 2 on the lower control panel and in the character information display on the monitor screen.

For details of character information display on the monitor screen, see F4 (CHARA) in function menu page 4 (page 11-7) and setup menu item 005 (page 12-5).

Note

You cannot use the above procedure to cue up to a virtual shot mark.

The tape is played back, and the shot data displayed.

To delete the shot data

Once again hold down the ENTRY button, and press the PLAY button.

Example of shot data display

The shot data display appears as shown below.

 

 

 

 

 

 

 

 

 

 

 

 

MODEL NAME

DNW 0090

 

 

 

 

SERIAL NUMBER

010001

 

 

 

 

DATE

1998.05.11

 

 

 

 

TIME

 

12.55.10

 

 

 

 

CASSETTE NUMBER 0095

 

 

 

 

SHOT NUMBER

0052

 

 

 

 

 

 

 

 

 

 

 

 

ID1

AAAAAAAAAAAA

 

Camera IDs

 

 

ID2

BBBBBBBBBBBB

 

 

 

ID3

CCCCCCCCCCCC

 

 

 

 

 

 

 

 

ID4

DDDDDDDDDDDD

 

Recording

 

 

 

 

TCR 23:59:59:29

 

 

 

 

 

time code

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The details in the shot data depend on the shooting conditions. If because of the devices used there is no shot data on a part of the tape, it appears as blank.

Mark Shot 6 Chapter

6-3-5 Reading In Shot Data

When there is shot data (time, device, and other information about the shooting) written on the tape, you can read it in and display it on the monitor.

Displaying the shot data

Holding down the ENTRY button, press the PLAY button.

Z

PLAY button

ENTRY button

Displaying the shot data on the shot mark list

Turn the MULTI CONTROL knob to position the cursor on a separator in the shot mark list.

If there is shot data recorded when the immediately following shot mark was written, it appears in the display as shown below.

 

 

 

 

 

 

 

 

 

Model name (4 characters)

 

 

 

 

 

 

 

 

 

 

 

 

 

Model number (4 digits)

Serial number (6 digits)

 

 

 

 

Cassette number (4 digits)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SHOT

MARK

 

 

 

 

 

 

Shot data

 

 

 

 

 

 

 

(---

/180)

 

 

 

 

 

 

 

 

 

 

NO.

TIME

CODE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

First shot

 

 

 

 

 

*012345

-

DNW_

-

0123

-

4567

-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

011

S1

10:04:05:11

 

 

mark in the

 

012

R

10:05:35:24

 

 

group

 

013

V

10:07:05:02

 

 

 

 

 

 

----------------------------

 

 

 

 

 

014

R

10:08:35:04

 

 

 

 

 

 

015

S2

10:09:05:11

 

 

 

 

 

 

016

R

10:10:35:24

 

 

 

 

 

 

017

R

10:10:36:00

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

You can sort the shot marks in the list, based on the shot data. For details, see the next section.

Function

Chapter 6 Shot Mark Function

6-7