|
|
|
|
|
|
|
|
|
|
|
|
| 1 | 2 |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| EJECT |
ACCESS | SG DATA | SG DATA | SG DATA | SG DATA |
|
| EDIT REMOTE [9P iLINK] |
| KEY INH | ALARM |
|
| |||||
ANA SDI | ANA SDI | ANA SDI | ANA SDI | INPUT | VITC VIUB COUNTER VITC | REC INH |
|
| |||||||||
| AE8/EBU | AE8/EBU | AE8/EBU | AE8/EBU |
|
|
| ||||||||||
| dB OVER | dB OVER | dB OVER | dB OVER | i.LINK |
|
|
|
|
|
|
|
|
| |||
| 0 |
| 0 | 0 | 0 |
| SDI |
|
|
|
|
|
|
|
|
|
|
NETWORK |
|
| CMPST |
|
|
|
|
|
|
| JOG | VAR | |||||
|
|
|
|
|
|
|
|
| E | ||||||||
LOCAL |
|
| SG |
|
|
|
|
|
|
|
| TTL |
| ||||
REMOTE |
|
|
|
| HOURS | MINUTES | SECONDS |
| FRAMES | HU |
| ||||||
|
|
|
|
| S |
| |||||||||||
MONITOR |
|
| MONITOR |
|
| IMX[50 40 30] |
|
|
| ||||||||
|
| 1/2 | 3/4 | AUDIO | 625 |
|
|
| |||||||||
L | CH- | 15 | CH- 26 | CH- 37 | CH- 48 | 5/6 | 7/8 | 48CH | 1824BIT | 525 | DVCAM |
|
|
|
| ||
MIX |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| SHIFT |
|
R |
|
| AUDIO |
| INPUT SEL | VIDEO | COUNTER |
|
| SYS MENU |
| ||||||
MONITOR SEL | METER SEL | INPUT CH | INPUT SEL | SELECT | HOLD | MENU |
|
| |||||||||
|
| SUB | THUMB | SET RESET |
| ||||||||||||
| VARIABLE |
|
|
|
|
|
|
|
|
| CLIP | NAIL |
|
| |||
| REC |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| PRESET |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| PB |
|
|
|
|
|
|
|
|
| CLIP |
| ESSENCE |
| S.SEL | MARK1 |
|
PHONES |
|
|
|
|
|
|
|
|
|
| MENU |
| MARK |
|
|
| |
PREV | PLAY | NEXT |
|
| STOP | REC |
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
| IN |
|
| OUT |
|
| TOP | F REV | F FWD | END |
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| MARK2 |
|
3
1 Press the MENU button.
The menu appears in the time data display.
2 Press the RESET button.
The message “Init setup?” appears in the time data display.
To abandon operations and return to the setup menu display
Press the RESET button again.
3 Press the SET button.
The menu settings are reset to their factory default settings.
Switching between 525(U) line, 525(J) line and 625 line modes (menu item 013)To switch between 525(U) line, 525(J) line and 625 line operation modes, proceed as follows.
1
2 Turn the jog dial or shuttle dial to display menu item 013 in the time data display.
3 Hold down the SHUTTLE button, and turn the jog dial or shuttle dial to set menu item 013 to “on.”
4
5 Hold down the SHUTTLE button, and turn the jog dial or shuttle dial to select the line mode 525(U), 525(J) or 625.
6 Press the SET button.
7 Turn the unit off (press the on/standby switch to put the unit in the standby state).
Next time the unit is turned on (when the unit is put in the operating state by pressing the on/standby switch), it operates in the new mode.
Menu bank operations (menu items B01 to B13)This unit allows menu settings to be saved in what are termed “menu banks.” Saved sets of menu settings can be recalled for use as required.
To jump to menu item B01
You can recall any required menu by turning the jog dial or shuttle dial after pressing the MENU button.
If you press the MENU button first, then the COUNTER SELECT button, you can jump directly to menu item B01 or H01. The recalled menu item toggles between B01 and H01 every time you press the COUNTER SELECT button.
Saving the current active menu settings
Set one of basic menu items B11 “SAVE SETUP BANK- 1” to B13 “SAVE SETUP
Recalling settings from a menu bank
Set one of basic menu items B01 “RECALL SETUP
To recall menu bank 4, select
1) This is supported from firmware version 1.4.
Refer to the maintenance manual for more information about menu bank 4.
Menus 8 Chapter