Before Using the Unit
Setting the Line Mode
This unit is shipped with the line mode still unset. Therefore you need to set the line mode before using the unit. (The unit cannot be used unless the line mode is set.) Once it is set, the line mode is retained even when the unit is powered off.
Setting procedure
Use the following procedure to set the line mode.
1
POWER switch (rear panel) |
| 2,3 | ||||||||||||||||
|
|
|
|
|
|
|
|
| Time data display |
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| EJECT |
ACCESS | SG DATA | SG DATA | SG DATA | SG DATA |
|
| EDIT REMOTE [9P iLINK] |
| KEY INH | ALARM |
|
|
| |||||
ANA SDI | ANA SDI | ANA SDI | ANA SDI | INPUT | VITC VIUB COUNTER VITC | REC INH |
|
|
| |||||||||
| AE8/EBU | AE8/EBU | AE8/EBU | AE8/EBU |
|
|
|
| ||||||||||
| dB OVER | dB OVER | dB OVER | dB OVER | i.LINK |
|
|
|
|
|
|
|
|
|
| |||
| 0 |
| 0 | 0 | 0 |
| SDI |
|
|
|
|
|
|
|
|
|
|
|
NETWORK |
|
| CMPST |
|
|
|
|
|
|
| E | JOG | VAR | |||||
|
|
|
|
|
|
|
|
|
| |||||||||
LOCAL |
|
| SG |
|
|
|
|
|
|
|
| TTL |
|
| ||||
REMOTE |
|
|
|
| HOURS | MINUTES | SECONDS |
| FRAMES | HU |
|
| ||||||
|
|
|
|
| S |
|
| |||||||||||
MONITOR |
|
| MONITOR |
|
| IMX[50 40 30] |
|
|
|
| ||||||||
|
| 1/2 | 3/4 | AUDIO | 625 |
|
|
|
| |||||||||
L | CH- | 15 | CH- 26 | CH- 37 | CH- 48 | 5/6 | 7/8 | 48CH | 1824BIT | 525 | DVCAM |
|
|
|
|
| ||
MIX |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| SHIFT |
|
|
R |
|
| AUDIO |
| INPUT SEL | VIDEO | COUNTER |
|
| SYS MENU |
|
| ||||||
MONITOR SEL | METER SEL | INPUT CH | INPUT SEL | SELECT | HOLD | MENU |
|
|
| |||||||||
|
| SUB | THUMB | SET RESET |
|
| ||||||||||||
| VARIABLE |
|
|
|
|
|
|
|
|
| CLIP | NAIL |
|
|
| |||
| REC |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| PRESET |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| PB |
|
|
|
|
|
|
|
|
| CLIP |
| ESSENCE |
| S.SEL | MARK1 |
|
|
PHONES |
|
|
|
|
|
|
|
|
|
| MENU |
| MARK |
|
|
|
| |
PREV | PLAY | NEXT |
|
| STOP | REC |
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
| IN |
|
| OUT |
|
|
| TOP | F REV | F FWD | END |
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| MARK2 |
|
|
54
1 Power the unit on.
“Select | ” appears in the time data display. |
|
|
|
|
2 With the SHUTTLE button held down, rotate the jog dial.
When you rotate the jog dial in the forward direction, the
Setting | Line mode |
|
|
525U | 525(U): NTSC (areas outside Japan) |
|
|
525J | 525(J): NTSC (Japan) |
|
|
Setting | Line mode |
|
|
625 | 625: PAL |
|
|
3 When the desired setting appears, release the SHUTTLE button.
“Push SET !!” appears.
To redo the selection
Repeat step 2.
4 Press the SET button.
“Turn OFF !!” appears.
5 Power the unit off, and then power it on again.
The selected line mode becomes available for use.
You can change the setting made with this procedure by using basic menu item 013 “525/625 SYSTEM SELECT.” See
105)for more information about how to make basic menu settings.
Note
The line mode is not set, or is cleared, in the following situations. Reset the line mode.
•The unit is powered off before performing step 4 in the previous procedure.
•The “RESET ALL SETUP” command in the maintenance menu (see page 124) is executed.
Settings affected by the line mode
The following settings are affected when the line mode is changed.
•Alarm message language 525(J): Japanese 525(U)/625: English
•The following menu item names, setting values, or factory default setting values
Before Using the Unit 13