2-2 Rear Panel

1 REF. VIDEO IN connectors

REF.VIDEO IN

 

 

VIDEO IN VIDEO OUT

3Analog video signal inputs/

 

 

 

1

2

 

 

 

 

 

 

(SUPER)

 

 

 

 

 

 

 

 

outputs (see page 28)

 

 

AUDIO IN

1/3

2/4

AUDIO OUT 1/3

2/4 AUDIO

 

 

 

 

 

 

 

MONITOR OUT

 

1 Analog audio signal inputs/

 

 

 

 

 

5 AUDIO MONITOR OUT connector

outputs (see page 28)

 

 

 

 

 

 

 

DIGITAL AUDIO (AES/EBU)

 

SDI

 

TIME CODE

4Time code inputs/outputs

 

S400 IN 1/2

3/4 OUT 1/2

3/4 IN

OUT 1

2 (SUPER) IN

OUT

2

S400 (i.LINK) connector

 

 

 

 

 

(see page 29)

 

 

 

 

 

 

 

 

REMOTE

 

 

 

 

 

 

3 REMOTE connector

 

 

 

 

 

5Power supply section

 

 

 

 

 

(see page 29)

4

(network) connector

 

 

 

 

 

 

2Digital audio signal inputs/outputs

 

 

 

 

 

6 SDI signal inputs/

(see page 28)

 

 

 

 

 

outputs (see page 29)

Parts of Functions and Names 2 Chapter

aREF. VIDEO IN (reference video signal input) connectors (BNC type)

The two connectors form a loop-through connection; when a reference video signal is input to the left connector, the same signal is input from the right connector () to a connected device. When no connection is made to the right connector, the left connector is automatically terminated with an impedance of 75 ohms.

bS400 (i.LINK) connector (6-pin, IEEE1394

compliant)

Connect a DV device, computer, or similar, using an i.LINK cable.

When the unit is shipped from the factory, the audio output signal is set to 16 bit/48 kHz/2ch mode. You can change the audio mode and output channel settings with extended menu item 831 “DV OUT AUDIO MODE” and extended menu item 828 “SDI/DV AUDIO OUTPUT SELECT.”

See 8-3-2 “Extended Menu Operations” (page 120) for more information about how to make these settings.

Notes

•If video or audio signals from an external device

connected with the S400 (i.LINK) connector are not output, disconnect the i.LINK cable and connect it again, pushing it straight in.

•When the PDW-1500 is connected to a device with a 6- pin i.LINK connector by an i.LINK cable, before unplugging the i.LINK cable, first power off the device and disconnect the power plug from the outlet. If the i.LINK cable is unplugged with the device power plug still connected, a current from an excessive voltage (8 to

40 V) output from the i.LINK connector of the device flows into the PDW-1500. This may cause a failure of the PDW-1500.

•When connecting the PDW-1500 to a device with a 6-pin i.LINK connector, connect to the 6-pin i.LINK connector of the other device first.

•Except in playback mode (jog and shuttle modes, etc.), if you are monitoring the audio signal output from this connector on another device, the audio signal may sound differently from the audio signal played back on the PDW-1500.

cREMOTE (remote control signal) connector (D-

sub 9-pin)

To control the PDW-1500 from a controller or VTR supporting the RS-422A Sony 9-pin VTR protocol, connect the device to this connector.

d(network) connector (RJ-45 type)

This is a 10Base-T/100Base-TX/1000Base-T connector for network connection.

CAUTION

For safety, do not connect the connector for peripheral device wiring that might have excessive voltage to this port. Follow the instructions in this manual when making connections.

ATTENTION

Par mesure de sécurité, ne raccordez pas le connecteur pour le câblage de périphériques pouvant avoir une tension excessive à ce port. Suivez les instructions pour ce port.

2-2 Rear Panel 27