Menus 8 Chapter

Menu items in the 700s, relating to video control

Item number

Item name

Settings

 

 

 

 

726

H BLANKING WIDTH

 

Select the horizontal blanking width of the output analog video signal.

 

 

 

 

 

narow (narrow): Digital blanking (narrow)

 

 

 

 

 

wide: Analog blanking (wide)

 

 

 

 

 

When “wide” is selected, the horizontal blanking width complies with

 

 

 

 

 

RS170A, and normally the blanking is widened and the image becomes

 

 

 

 

 

narrower. It is recommended to select “narow” at the editing stage, then

 

 

 

 

 

later, for broadcast transmission to select “wide,” to output a signal

 

 

 

 

 

conforming to the standard. Note, however, that “narow” has to be always

 

 

 

 

 

selected for SDI signals.

 

 

 

 

728

OUTPUT SCH PHASE

 

Set the subcarrier H phase.

 

 

 

 

 

–512 (–512 (DEC))... 0 (0 (DEC))... 511 (511 (DEC))

 

 

 

 

731

WIDE MODE a)

 

Specify whether to record and play back with the addition of wide picture

 

 

 

 

 

information.

 

Sub-item

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

INPUT

 

Specify whether to save wide picture information on a disc during

 

 

 

 

 

recording.

 

 

 

 

 

auto: Automatically record wide picture information when it is detected in

 

 

 

 

 

 

the selected input video signal.

 

 

 

 

 

on: Always record wide picture information.

 

 

 

 

 

off: Do not record wide picture information.

 

 

 

 

 

 

 

2

 

OUTPUT

 

Specify whether to add wide picture information to the output signal

 

 

 

 

 

during MPEG IMX playback.

 

 

 

 

 

thru (through): Output the video signals of the disc being played back

 

 

 

 

 

 

without adding wide picture information.

 

 

 

 

 

auto: When wide picture information is detected on the disc being played

 

 

 

 

 

 

back, add wide picture information to the output video signals.

 

 

 

 

 

 

 

 

 

 

 

 

Notes

 

 

 

 

 

•

To add wide picture information to the output signal, it is necessary, in

 

 

 

 

 

 

addition to setting this item to “thru,” to operate extended menu item

 

 

 

 

 

 

703 to set line 20 (in 525 line mode) to “thru” or set line 23 (in 625 line

 

 

 

 

 

 

mode) to “thru.”

 

 

 

 

 

•

In 525 line mode, wide picture information may not be output if VITC

 

 

 

 

 

 

signal insertion position is set to line 20 in extended menu item 601 or

 

 

 

 

 

 

602.

 

 

 

 

 

 

 

 

 

a) This is supported from firmware version 1.4.

Menu items in the 800s, relating to audio control

Item number

Item name

Settings

 

 

 

802

DIGITAL AUDIO MUTING IN

Set the audio muting conditions during shuttle playback.

 

SHUTTLE MODE

off: Not muted.

 

 

on: Muted.

 

 

 

807

AUDIO OUTPUT PHASE

Set the output timing of digital audio playback signals (SDI, AES/EBU

 

 

only), with 80H as a reference position. Output timing is earlier for values

 

 

smaller than 80H and later for values greater than 80H. (80H, 128

 

 

samples = approx. 2.7 ms, 80H, 1 sample = approx. 20 μs)

 

 

0 (0 (HEX))... 80 (80 (HEX))... FF (FF (HEX)): Values can be set in this

 

 

range.

 

 

 

808

INTERNAL AUDIO SIGNAL

Select the operation of the internal audio test signal generator.

 

GENERATOR

silnc (silence): Silent signal.

 

 

1kHz (1kHz sine): 1 kHz, –20 dB FS sine wave signal.

 

 

When you select SG as the audio input in the input selection section of

 

 

the control panel, the audio test signal generated by the internal audio

 

 

test signal generator is input.

 

 

 

815

AUDIO SAMPLING RATE

Select the mode of operation of the sampling rate converter for AES/

 

CONVERTER

EBU input to channels 1 to 4.

 

 

off: Do not operate.

 

 

on: Operate.

 

 

 

118 8-3 Extended Menu