3-5-5 Formatting a Disc
An unused disc requires no formatting operation. The disc is automatically formatted when loaded into this unit.
To format a recorded disc, load the disc into the unit, then proceed as follows.
Note
When a recorded disc is formatted, all the data on the disc is erased. (Locked clips (see page 62) are also erased.)
|
|
|
|
|
|
|
|
|
| 1,6 |
| 1 |
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| EJECT |
ACCESS | SG DATA | SG DATA | SG DATA | SG DATA |
|
| EDIT REMOTE [9P iLINK] |
| KEY INH | ALARM |
|
|
| ||||
ANA SDI | ANA SDI | ANA SDI | ANA SDI | INPUT | VITC VIUB COUNTER VITC | REC INH |
|
|
| ||||||||
| AE8/EBU | AE8/EBU | AE8/EBU | AE8/EBU |
|
|
|
| |||||||||
| dB OVER | dB OVER | dB OVER | dB OVER | i.LINK |
|
|
|
|
|
|
|
|
| |||
| 0 |
| 0 | 0 | 0 |
| SDI |
|
|
|
|
|
|
|
|
|
|
NETWORK |
|
| CMPST |
|
|
|
|
|
| E | JOG | VAR | |||||
|
|
|
|
|
|
|
|
| |||||||||
LOCAL |
|
| SG |
|
|
|
|
|
|
| TTL |
|
| ||||
REMOTE |
|
|
|
| HOURS | MINUTES | SECONDS | FRAMES | HU |
|
| ||||||
|
|
|
| S |
|
| |||||||||||
MONITOR |
|
| MONITOR |
|
| IMX[50 40 30] |
|
|
|
| |||||||
|
| 1/2 | 3/4 | AUDIO | 625 |
|
|
|
| ||||||||
L | CH- | 15 | CH- 26 | CH- 37 | CH- 48 | 5/6 | 7/8 | 48CH | 1824BIT | 525 | DVCAM |
|
|
|
| ||
MIX |
|
|
|
|
|
|
|
|
|
|
|
|
|
| SHIFT |
|
|
R |
|
| AUDIO |
| INPUT SEL | VIDEO | COUNTER | HOLD | SYS MENU |
|
| ||||||
MONITOR SEL | METER SEL | INPUT CH | INPUT SEL | SELECT | MENU |
|
|
| |||||||||
|
| SUB | THUMB | SET RESET |
|
| |||||||||||
| VARIABLE |
|
|
|
|
|
|
|
|
| CLIP | NAIL |
|
| |||
| REC |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| PRESET |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| PB |
|
|
|
|
|
|
|
|
| CLIP |
| ESSENCE | S.SEL | MARK1 |
|
|
PHONES |
|
|
|
|
|
|
|
|
|
| MENU |
| MARK |
|
|
| |
PREV | PLAY | NEXT |
|
| STOP | REC |
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
| IN |
| OUT |
|
|
| TOP | F REV | F FWD | END |
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| MARK2 |
|
|
52,3,4
1Holding down the SHIFT button, press the MENU button.
The system menu appears on the monitor screen.
2Select “DISC MENU” using the F button or f button, then press the g button.
The menu item “FORMAT” is displayed.
3Select “FORMAT” using the F button or f button, then press the g button.
The menu item “QUICK FORMAT” is selected.
4Press the g button.
The message “QUICK FORMAT OK?” appears.
To return to the previous menu page without formatting the disc
Press the RESET button.
5Press the SET button.
Formatting is completed and the message “FORMAT COMPLETED.” appears.
6Press the MENU button. This exits the menu.
To format several discs in succession 1)
1 Carry out steps 1 to 5 in the previous procedure, and then press the EJECT button to eject the disc.
2 Insert the next disc that you want to format.
The message “QUICK FORMAT OK?” appears.
3 Press the SET button.
4 When the message “FORMAT COMPLETED.” appears, press the EJECT button to eject the disc.
5 Repeat steps 2 to 4 for all of the discs that you want to format.
1) This is supported from firmware version 1.4.
3-5-6 To Eject Discs With the Unit Powered Off
As an emergency measure, disc cartridges can be removed with the unit powered off. However, the cover must be removed. This operation should always be done by a trained service technician.
For details, refer to the Maintenance Manual.
3-5-7 Handling of Discs When
Recording Does Not End
Normally (Salvage Function)
Recording processing does not end normally if, for example, the POWER switch on the rear panel is turned off during recording, or if the power cord is disconnected during recording. Because the file system is not updated, video and audio data recorded in real time is not recognized as files and clip contents recorded up to that point are lost.
However, this unit has a salvage function which can hold losses to the minimum by reconstructing clips on such discs.
Note that no recorded clip contents are lost when the on/ standby switch on the front panel is set to standby, because the unit does not enter standby mode until after the end of recording processing.
Notes
•Do not set the POWER switch on the rear panel to off until recording processing has finished and the ACCESS indicator has gone out.
Preparations 3 Chapter