Menu items in the 800s, relating to audio control

Item number

Item name

Settings

 

 

 

 

 

828

SDI/DV AUDIO OUTPUT SELECT

Select the audio signals to assign to SDI and i.LINK(AV/C) audio output

 

s

 

 

channels.

 

 

 

 

 

 

Sub-item

 

 

 

 

 

 

 

1

CH1/CH2

tr1/2: Tracks 1 and 2 assigned to audio output channels 1 and 2.

 

 

 

 

tr3/4: Tracks 3 and 4 assigned to audio output channels 1 and 2.

 

 

 

 

tr5/6: Tracks 5 and 6 assigned to audio output channels 1 and 2.

 

 

 

 

tr7/8: Tracks 7 and 8 assigned to audio output channels 1 and 2.

 

 

 

 

 

 

2

CH3/CH4

tr1/2: Tracks 1 and 2 assigned to audio output channels 3 and 4.

 

 

 

 

tr3/4: Tracks 3 and 4 assigned to audio output channels 3 and 4.

 

 

 

 

tr5/6: Tracks 5 and 6 assigned to audio output channels 3 and 4.

 

 

 

 

tr7/8: Tracks 7 and 8 assigned to audio output channels 3 and 4.

 

 

 

 

 

831

DV OUT AUDIO MODE

Select the audio mode for S400 (i.LINK) connector (output).

 

 

 

 

 

 

 

 

4ch: 12 bit/32 kHz/4ch

 

 

 

 

2ch: 16 bit/48 kHz/2ch

 

 

 

 

 

 

 

Menu items in the 900s, relating to digital process

 

 

 

 

 

Item number

Item name

 

Settings

 

 

 

 

920

SD-SDI H-ANC CONTROL

 

Select whether or not to add information to the SDI output.

 

 

 

 

 

Sub-item

 

 

 

 

 

 

 

 

1

AUDIO 5CH-8CH

 

off: Do not add digital audio data channels 5 to 8.

 

 

 

 

on: Add digital audio data channels 5 to 8.

 

 

 

 

 

 

2

RP188 ATC

 

off: Do not add RP188 time code data.

 

 

 

 

on: Add RP188 time code data.

 

 

 

 

 

Menus 8 Chapter

8-3-2 Extended Menu Operations

The extended menu can be used with the same procedures as in the basic menu.

However, since with the factory default settings the extended menu is not displayed, it is first necessary to enable display of the extended menu.

See 8-2-2 “Basic Menu Operations” (page 105) for more information about how to select menu items and how to change their values.

Enabling display of the extended menu

To enable display of the extended menu, an internal switch must be set to on, and extended menu display must be enabled in the maintenance menu. (The internal switch is set to on when the unit is shipped from the factory. Unless you have set it to off, there is no need to change the switch setting.)

To set the internal switch to on

1 Using a Phillips screwdriver, remove the cover.

There are five screws fixing the cover.

2 Using a sharp implement such as a ball-point pen, set switch 4 in the S2202 group to the ON position (on the inside).

Note

Do not use a pencil for this operation, as graphite deposits can cause short circuits and lead to failure.

120 8-3 Extended Menu