Toshiba MMU-AP0091MH Installation of Indoor Unit, Case of wireless type, Dimensional view

2 SELECTION OF INSTALLATION PLACE

In case of wireless type

The wireless remote controller can be operated up to a maximum of 8 m from the infra-red receiver.

Therefore ensure that the remote controller will be mounted and used within this stated parameter.

•To prevent malfunction do not mount or operate in a location that is subjected to either a fluorescent lamp or direct sunlight.

•A maximum of 6 indoor units with wireless remote controller can be installed within the same room.

3 INSTALLATION OF INDOOR UNIT

22	WARNING
	The installation of the air conditioning unit must be positioned in a location that can sufficiently support its weight
	and give protection against adverse environmental conditions.

Failure to do so may result in unit damage and possible human injury.

Any incomplete installation may also cause possible risk of human injury.

•Unpack the package, take out the product and then place it on the floor so that the same surface directs underneath as it is placed in the package.

•Never put the products taken out from the packing box in a

pile, or put other load on them; otherwise there is a	OK	NO GOOD
possibility to damage electric parts, fan parts, draining
mechanism, and etc.

If the both sides are turned over, a deformation of mounting metal of the ceiling panel which is sold separately, etc may be caused. Accordingly the product may be damaged and the installation becomes impossible in some cases.

REQUIREMENT

Strictly comply to the following rules to prevent damage of the indoor units and human injury.

•Do not place heavy objects on the indoor unit. (Even when units are still packaged)

•Always carry the unit as packaged from the factory wherever possible.

If carrying in the indoor unit unpacked by necessity, be sure to use buffering cloth, etc. to prevent damaging the unit.

•To move the indoor unit, hold the hanging brackets (4 positions) only.

Do not apply force to other parts (refrigerant pipe, drain pan, foamed parts, or resin parts etc.).

• To be carried by two or more persons. Do not strap the unit in positions other than that stated.

Dimensional view
1000 or more	1000 or more	595 to 660 Ceiling open dimension
	15 or more
	Obstacle

1000 or more

15 or more

Space required for

installation and servicing

207	175	149
		64	29	142	64	368.5

	Knockout for 100 diameter
	fresh air intake
145.5	Bottom face		700 Panel external dimension
93			595 to 660 Ceiling open dimension
	of ceiling
			525 Hanging bolt pitch
105	70
	235	dimension
	105	external
	235	575 Unit

Ø162
4 screw holes	Electric parts box	320.5
(For 4 mm tapping screw)
For 150 diameter	575 Unit external dimension
branch duct knockout
square hole
Bottom face of ceiling

					200
			Check port
dimension		200	(		450)			200
	Check port
	(o450)				Check port
						(	450)
Ceiling660open		Drain-up standing-up size
		300 or less	Stand-up	627.5	lessor	up-Stand	lessor850
	Indoor unit
			Ceiling
to	Note)
595
	As ABS is used for the drain discharge port of the main unit,
	the vinyl chloride paste cannot be used.

Use the flexible hose (Band fix) included in the package.

			4	2.7
•	Wired remote				120
	controller
	(RBC-AMT31E)
				120		16
			268		27
			220.5
	Drain discharge port			145.5
	Hanging bolt			134		Bottom face
						of ceiling
	M10 or W3/8			63
	local arrange				Ceiling panel
	Hanging525bolt pitch Ceiling660to595open dimension externalPanel700 dimension	105214 256
177			14842		21120	158142
			Ø162
	Refrigerant pipe		97.5		Wiring connection
				55	port
	(Liquid) Ø6.4

For 150 diameter 70 105 93
branch duct
		139.5
knockout square hole
Refrigerant pipe (Gas)	190.5
0151, 0181MH : Ø12.7
0071 to 0121MH : Ø9.5