|
| TROUBLESHOOTING | ||
|
|
|
| |
Problem | Cause | Remedy | Refer to | |
page | ||||
|
|
| ||
|
|
|
| |
The sound suddenly | The protection circuitry has been activated | Check that the correct impedance is set. | 28 | |
goes off. | due to a short circuit, etc. |
|
| |
Check that the speaker wires are not touching each | — | |||
|
| |||
|
| other and then turn this unit back on. |
| |
|
|
|
| |
| The sleep timer has turned the unit off. | Turn on the power, and playback the source again. | — | |
|
|
|
| |
| The sound is muted. | Press MUTE or any operation button on this unit to | 38 | |
|
| cancel mute and adjust the volume. |
| |
|
|
|
| |
The speaker on one | The cable connections are incorrect. | Connect the cables properly. If the problem persists, | 13 | |
side only can be |
| the cables may be defective. |
| |
heard. |
|
|
| |
The balance settings are incorrect. | Adjust the Speaker Level settings. | 69 | ||
| ||||
|
|
|
| |
No sound from the | The sound field programs are turned off. | Press STRAIGHT/EFFECT to turn them on. | 42 | |
effect speakers. |
|
|
| |
A Dolby Surround, Dolby Digital or DTS | Select another sound field program. | 39 | ||
| ||||
| decoding DSP program is being used with |
|
| |
| material not encoded with Dolby |
|
| |
| Surround, Dolby Digital or DTS. |
|
| |
|
|
|
| |
| A sampling digital signal of 96 kHz or |
|
| |
| higher is being input to this unit. |
|
| |
|
|
|
| |
No sound from the | The output level of the center speaker is | Raise the level of the center speaker. | 69 | |
center speaker. | set to minimum. |
|
| |
|
|
|
| |
| “Center” is set to None in Speaker Set. | Select the appropriate mode for your center speaker. | 67 | |
|
|
|
| |
| One of the | Select another sound field program. | 39 | |
| for 9ch Stereo) has been selected. |
|
| |
|
|
|
| |
No sound from the | The output level of the surround speakers | Raise the output level of the surround speakers. | 69 | |
surround speakers. | is set to minimum. |
|
| |
|
|
|
| |
| “Surround” is set to None in Speaker Set. | Select the appropriate speaker mode for the surround | 68 | |
|
| L/R speakers. |
| |
|
|
|
| |
| A monaural source is being played with | Press STRAIGHT/EFFECT to turn on the sound | — | |
| STRAIGHT/EFFECT set to STRAIGHT. | fields. Then select another sound field program. |
| |
|
|
|
| |
No sound from the | “Surround” is set to None in Speaker Set. | If the speaker mode for the surround L/R speakers is | 68 | |
surround back |
| set to None, the speaker mode for the surround back |
| |
speakers. |
| speaker is automatically set to None. Select the |
| |
|
| appropriate speaker mode for the surround L/R |
| |
|
| speaker mode. |
| |
|
|
|
| |
| “Surround Back” is set to None in Speaker | Select Large or Small. | 68 | |
| Set. |
|
| |
|
|
|
| |
No sound from the | “Bass Out” is set to Front in Subwoofer | Select SWFR or Both. | 67 | |
subwoofer. | Set when a Dolby Digital or DTS signal is |
|
| |
| being played. |
|
| |
|
|
|
| |
| “Bass Out” is set to SWFR or Front in | Select Both. | 67 | |
| Subwoofer Set when a |
|
| |
| being played. |
|
| |
|
|
|
| |
| The source does not contain low bass |
|
| |
| signals. |
|
| |
|
|
|
| |
| INFORMATION | ADDITIONAL |
|
|
|
|
|
|
| English |
|
|
|
|
109