TROUBLESHOOTING
Problem | Cause | Remedy | Refer to | |
page | ||||
|
|
| ||
|
|
|
| |
There is noise | This unit is too close to digital or high- | Move this unit further away from such equipment. | — | |
interference from | frequency equipment. |
|
| |
digital or high- |
|
|
| |
frequency equipment, |
|
|
| |
or this unit. |
|
|
| |
|
|
|
| |
The picture is | The video source uses scrambled or | Playing back video software that has an | — | |
disturbed. | encoded signals to prevent dubbing. | signal or video signals with a lot of noise may |
| |
|
| produce unstable images. |
| |
|
|
|
| |
This unit suddenly | The internal temperature has become too | Wait until this unit cools down and then turn it back | — | |
switches to the | high and the overheat protection circuitry | on. |
| |
standby mode. | activated. |
|
| |
|
|
|
| |
Monitor output fails. | The wrong TV format is set. | Press and hold down EXIT on the remote control for | 71 | |
|
| 5 seconds or longer to initialize Video settings. |
| |
|
|
|
|
■Remote control
Problem | Cause | Remedy | Refer to |
| |
page |
|
| |||
|
|
|
| ||
|
|
|
|
|
|
The remote control | The remote control is being used at the | The remote control will function within a maximum | 9 |
|
|
does not work or | wrong distance or angle. | range of 6 m (20 ft) at no more than 30 degrees off- |
|
|
|
function properly. |
| axis from the front panel. |
|
|
|
|
|
|
|
| |
| Direct sunlight or lighting (from an | Reposition this unit. | — |
|
|
| inverter type fluorescent lamp, etc.) is |
|
|
|
|
| striking this unit’s remote control sensor. |
|
|
|
|
|
|
|
|
|
|
| The batteries are weak. | Replace all batteries. | 4 |
|
|
|
|
|
|
|
|
| The manufacturer code was not set | Set the manufacturer code correctly. | 81 |
|
|
| correctly. |
|
|
|
|
| Try setting another code for the same manufacturer. | 81 |
|
| |
|
|
|
| ||
|
|
|
|
|
|
| Even if the manufacturer code is correctly | Program the necessary functions independently for | 82 |
|
|
| set, there are some models that do not | the programmable buttons using the learn feature. |
|
|
|
| respond to the remote control. |
|
|
|
|
|
|
|
|
|
|
The remote control | The batteries of this remote control and/or | Replace the batteries. | 4 |
|
|
does not “learn” new | the remote control for your component are |
|
|
|
|
functions. | too weak. |
|
|
|
|
|
|
|
|
|
|
| The distance between the two remote | Place the remote controls at the proper distance. | 82 |
|
|
| controls is too long or too short. |
|
|
|
|
|
|
|
|
| |
| Signal coding or modulation of the remote | Learning is not possible. | — |
|
|
| control for your component is not |
|
|
|
|
| compatible with this remote control. |
|
|
|
|
|
|
|
|
|
|
| Memory capacity is full. | Delete unnecessary functions to make room for new | 86, 87 |
|
|
| ADDITIONAL INFORMATION | ||||
|
| functions. |
|
| |
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| English |
|
|
|
|
|
|
111