Manuals / ZyXEL Communications / Computer Equipment / Network Router

ZyXEL Communications omni series user manual Extended AT& Command Set

Models: omni series

1 168

Download 168 pages 22.94 Kb

Page 130

Output Parameter	Output Value Description
Connect DTE Speed	Current on-line DTE speed.
Error Control Level	Error control protocol used for current
	session.
Protocol Link Speed	Current on-line DCE speed, line speed.
Octets Received	Number of data octets received from
	remote.
Octets Sent	Number of data octets sent to remote.
Cause	Verbose disconnection reason for the last
	session.
Cause Value	Numerical disconnection reason for the last
	session.
HDLC FCS Error	Errors in frame (block) checksum (If there
	were many FCS Errors, you may have
	experienced problems on the line).
HDLC Transmit	For TA's processor power measurement.
Under-run
HDLC Receive	For TA's processor power measurement.
Over-run

Extended "AT&" Command Set

Command	Options	Function & Description	Ref.
&Cn		Carrier Detect (CD) options	S21.4
	&C0	CD always ON (See also S42.7)
	&C1 *	CD tracks presence of carrier (See
		also S38.3, S42.7)
&Dn		Data Terminal Ready (DTR) options.	S21.6-7
		(See also S25)
	&D0	Ignore DTR signal, assume DTR is
		always ON.
	&D1	108.1, DTR OFF-ON transition
		causes dial of the default number.
		(See also 'AT*Dn' and S48.4)
	&D2 *	108.2, Data Terminal Ready, DTR
		OFF causes the TA to hang up.

118 AT Command Set Reference

Image 130

ZyXEL Communications omni series user manual Extended AT& Command Set

Contents

ZyXEL ZyXEL Limited Warranty Copyright 1997 by ZyXEL FCC Part 15 InformationAcknowledgments Page Contacting ZyXEL ∙ E-mailPage Contents Outgoing Calls Understanding AT CommandsInstalling the Windows 95 Driver INF file Incoming CallsError Correction and Data Compression with Configuring Windows 95 Dial-Up Networking Capi InstallationIntroduction Feature list Placing outgoing callsCall Control for DSS1 Answering an X.75 call Making an X.75 CallInvoking V.42bis Data Compression Call Control for 1TR6 Old German IsdnPlacing a Call Diagnostics 100Resetting The omni 103 Using The Embedded Protocol Analyzer Upgrading with Flash EpromViewing and Setting S-Registers 125 AT Command Descriptions 109Register Descriptions 127 Introduction Key to Model Differentiation Key Features of the omniSpeed and Compatibility Intelligent Features Technical SpecificationsUnpacking Your omni Physical CharacteristicsInterface Option How to Become a Registered Owner Introduction LED Indicators Installing omni External ModelsFront Panel Page Front Panel Switch Back PanelConnecting to the Power Supply Connecting to Your ComputerConnecting the omni.net to Your Computer Connecting to Your Isdn Line Interface ModelPower On and Self Diagnostics InterfaceInstalling omni External Models Installing omni Internal Models Selecting the Baud Rate MultiplierConnecting the TA to your PC Plug and PlayPress Y to continue Following message will appear Connecting to Your Isdn Line Interface Model Omni.net Internal Card Installation S/T interface Configuring your TA using a Terminal program Configuring Your Isdn Line and NetworkConfiguring Your TA Type A\setup.exe and press EnterTA should respond Type Page Configuring Your Isdn Line and Network Understanding AT Commands Isdn Communication BasicsQuick Tips when issuing AT commands Supported AT command typesType of AT Command Example Outgoing Calls Dialing out using Isdn modeCommand Description ATV0Dialing out for Analog Adapter Port 1 omni.net Dialing out for Analog Adapter Port 1 omni.net InternalDialing out for Analog Adapter Port 2 omni.net Incoming Calls Manually switching communication modes non-dataAT Command Dial string it will map to Placing the CallDigital Data Determining the Packet LengthAnswering a Call using MSN AT&ZIn=s where ‘s’ is the MSN Data over Speech Channel Ambiguity resolution switch for voice calls omni.netCommand Function Best-effort call answering non-dataMulti auto-answering of data calls Setup for Windows 95 and NT Installing the Windows 95 Driver INF filePage Page Configuring Windows 95 Dial-Up Networking Page Page Click on TCP/IP Settings IPX/SPX CompatibleCapi Installation Page Point-to-Point Protocol PPP IntroductionFeature list Async to Sync Conversion externalCompression Control Protocol CCP Multilink PPP Bandwidth On Demand BOD BACP/BAP Point-to-Point Protocol PPP 110 and Synchronous Mode Communications Answering a V.110 callMaking V.110 Calls AT Command DescriptionSynchronous Connections external CIC 25bis Command SetCommand Messages DICIndicator Messages DTR Drop-Dialing OperationAT*D0 56 V.110 and Synchronous Mode Communications 120 Isdn Communications Placing outgoing callsConfiguring the V.120 mode Dialing in V.120 mode Answering incoming callsIdentifying your line provisioning Speeds of 128KbpsMaking a Bundled Call with Dialing pre-stored phone numbers Error Correction and Data Compression with Selecting V.120 for Germany National Isdn 1TR6 Selecting V.120 for European Isdn DSS1Bundle Connection with V.42bis Data Compression Page 10 X.75 Isdn Communications Answering an X.75 call Making an X.75 CallATDIphonenumber1+phonenumber2 Invoking V.42bis Data Compression Bundle Connection with V.42bis Data Compression 70 X.75 Isdn Communications AT&V6 Handling Analog Calls non-dataAT&V7 European switch specific Placing a Call from the Analog AdapterAccepting an Incoming Call Scenarios of an Incoming Voice Call OutcomeAT Commands Description Flash key Feature Phone omni.netCommands Description InterComPlacing a second call Call WaitingReceiving a second call Call Transfer Call BrokerCall Reject Three-way Conference CallHFlash è H#3 Advanced Isdn Call Control Control of Outgoing Service IndicatorCall Control for DSS1 S80 bit ‘n’ as follows S108+n= FunctionS108.n= Function Control of Isdn Phone Number and Sub-address = YnNnown-number/Znown-SubaddressCall Control for 1TR6 Old German Isdn Modem Control of Endgerä Teauswahlziffer EAZG3 Fax Command Function Answering a Call Answering a Call for DSS1Answering a Call for 1TR6 Best-effort Call AnsweringMulti-Auto-Answering of Data Calls Ambiguity Resolution Switch for Voice Calls non-dataData Call Indication Disable inbound call connection Placing a call for DSS1 Point-to-Point ConfigurationPlacing a Call ATDxYnNncalledpartynumber/Zncalled-party- subaddressPlacing a call for 1TR6 Leased Line Isdn ATDB3 ATDB1ATDB2 ATAB1Security Functions Security Types and LevelsLevel 3 security Level 1 securityLevel 2 security LevelSetting and Modifying Passwords Non-password Auto Call Back Function Security Functions Upgrading Your omni Upgrading with Flash EpromKernel Mode Test DiagnosticsDiagnostics Test DescriptionIsdn Loopback test AT&T9 Power-on Self-testLoopback with Self-test AT&T10 Diagnostic Command Atcg B1/B2 Loopback with Self-test AT&T11Resetting The omni Using The Embedded Protocol AnalyzerCapturing the Protocol Data CB0 CD0CD1 CB1ATC$ Key Function DescriptionDiagnostics Multiplex mode AT Command Set ReferenceSimplex mode Operation Modes of the DTE InterfaceAT Command Descriptions Basic AT Command SetCommand Options Function & Description All the Following Commands Require a AT PrefixBP1 BP0CE0 CL? CE1CH? CP0Command Options Function & Description DB3 DB1DB2 DN?ATI USASPID1 IsdnSPID0 SPID?UPX Description of ATI3 OutputOutput Parameter Output Value Description Extended AT& Command Set Isdn Command Options Function & Description Command Options Function & Description Extended AT* Command Set Command Options Function & Description AT Command Set Reference Status Registers and Result Codes Viewing and Setting S-RegistersViewing S-registers Setting S-registers Operation Example-1 Example-2 Binary Dec Hex Register DescriptionsBit Binary value Decimal value Hexadecimal value NotBasic S-Registers ATSn=x Command Function & DescriptionCommand Bit Dec Hex Function and description Extended S-Registers ATSn=xCommand Bit Dec Hex Function and description ATX1 ATX0ATX2 ATX3 ATX4 Command Bit Dec Hex Function and description Command Bit Dec Hex Function and description Command Bit Dec Hex Function and description Complete Command Bit Dec Hex Function and description Enable loopback 4 test DCA function enabled Command Bit Dec Hex Function and description SI= Fernsprechen analog 48000 bps PPP/MLPPP Command Bit Dec Hex Function and description PPP ATXn Result Code Option Table ATV0 ATV1Connect Result Code Field Descriptions Result Code Chart Symbol ReferenceField Name Possible Values Connect Strings for Error Corrected Connections Status Registers and Result Codes Phone Jack Pinout Assignments Not Connected Phone Jack Pinout Assignments Pin Signal/Pin Number Description Direction NameSerial Port Interface DCETXD RXD RTS CTS DSR DTEMAC CD DCD DTRIndex IndexBundled Index