DCS 500 manual Pin/Parameter Selecting and Changing of Value, Drive Mode

Page 41

					Chapter 3 - Handling of Control Panel CDP 31x
Drive Mode	Drive mode is used to check the configuration. The display will
	show the type and ID-number of the drive to whom the CDP 31x is
DRIVE	connected to.
DRIVE

		Drive Display
		Device type		DCS500
		Device type

		The ID-number		ID-NUMBER 0
		The ID-number		ID-NUMBER 0
		Total number
		of drives in		TOTAL 1 DRIVES
		the link		TOTAL 1 DRIVES

Display with CDP 310 / CDP 311

The factory-adjusted (default) values of the ID-numbers for the

CDP and the drive depend on the specific CDP type:

CDP 310 / CDP 311 ⇒		ID = 31	with	DCS 500	⇒	ID = 0
CDP 312	⇒	ID = 0	with	DCS 500B	⇒	ID = 1

Caution: These values should not be changed!

DCS500

ID=0

Control Panel

ID=31

1 L 30.5 %		00
FLUX_REF	100%
EXMF_FLS	0	Log
ARMCURAC	147	A

CDI 300 link

(communication bus)

Factory-adjusted (default) values for CDP 310 / CDP 311 with DCS 500

3.4 Pin/Parameter Selecting and Changing of Value

For input / parameter selection, the following applies:

•Ignore the two right-hand digits; the remaining digits are the group and to be selected

•The two right-hand digits are the element and to be selected

DI7	10713 Group 107
	element 13

The selection can be done with the control panel CDP312, using

the keys / for the group and the keys / for the element or a PC-based tool program CMT/DCS500B

DCS 500B / DCP 500B Operating Instructions

IV A 3 - 5

3ADW000055R0401_DCS500B_Operating Instruction_e_d

Image 41

Contents DCS 500B / DCF 500B DCP 500B How the DCS 500 Documentation System works Operating Instructions DCS 500B / DCP 500B Operating Instructions Overview Safety InstructionsSafety Instructions Mains connection Emergency Stop buttons Intended use Contents Signals and Troubleshooting DCS 500B / DCP 500B Operating Instructions Contents of this manual How to use this manualTarget group Associated publicationsRating plate Incoming inspectionStorage and transport How this chapter is structured General notesRecommended motor voltages and field voltages = Line voltageMethod of functioning of the binary inputs DI5, DI7 and DI8 System-dependent planning Symbols for enabling / disabling the referenceSymbol for measuring physical variables Symbol for displaying parameter values or connectionsPreparatory work Scaling intra-unit signals Set this only for units of the DCP 500 series 518 = 500 V fixed! rated power converter voltage519 11202 = Save MOT1 SET1305 = Field current for Under-excitation signal Presetting the field supply unitIV a 2 1201 = 3 Panel display ARM. Autotuning Adjusting the current controllerDCS 500B / DCP 500B Operating Instructions IV a 2 Speed feedback balancing Only when the e.m.f. signal is being used as speed feedback Continue with Chapter Balancing the field supply unit and the e.m.f. controllerField weakening control with setting range 1 11209 = If the field time constant is not known1204 = 1205 = 1002 = 1201 = 0 Panel display not Activated 11202 = Save MOT1 SET1004 = 1009 = 1010 == decrease so that motor voltage is 70% 11003Proceed as described in 1. / 2. / 3. above = decrease so that motor voltage is 40%12516 = increase slowly up to 20000 =100 % speed Only if analog tacho is used as speed feedback1204 POT1 = 10%...20% max. speed 1708 = 0,1 s 1709 = 0,1 s408 = desired response behaviour of controller 1008 = desired response behaviour of controller1204 = 1205 = Presetting the 3-phase field supply unit DCF 50xB 3601 = 1201 = 5Panel display FEX2/3 Autotuning3602 = 3603 =1201 = 4Panel display ARM. MAN. Tuning ⇒ CDP ⇒ CDP 310 or CDPID-NUMBER Total 1 Drives Start ModePanel Functions ACTPAR Pin/Parameter Selecting and Changing of Value Drive ModeValue To enter the Parameter ModeBackupstoremode Saving of the Parameters to backup memoryDisplay Mode Fault Resetting ResetFault History Display DCS Uploading and Downloading of Parameters UPLOAD/DOWNLOADDCS 500B / DCP 500B Operating Instructions IV a 3 Display Mode release key Setting of the Display ContrastFull Name of output pins Selecting output pins Drive Mode Operational Com- mand Keys Running the DriveTo enter the Reference Setting Speed Reference Setting for the DriveTo exit the Reference Setting ModeDisplay of status, alarm and fault signals Signals and TroubleshootingGeneral messages Starting errors EAuxil. undervoltage Fault Signals FMotor 1 overtemp Conv.fan curr.faultEarth fault SDCS-IOB-3, SDCS-POW P418Local & discon Ext.Overvolt.FaultNected Limited by the activation of a free wheeling CircuitCheck Parameters of Field Exciter Field ex.1 comerrorMains overvoltage Arm. curent ripple No ext. FAN ack See Fault Code FNo main cont. ack Field ex.1 not OKIV a 4 Current Difference Reversal Fault103 Motor 1 temp. alarm Alarm Signals aCheck See Fault Code F 105 Conv. overtemp 101 Start inhibition110 108118 120128 127129 130136 134137 138At Macro x, macro-specific links or function 11201 Status SignalsBackupstoremode Fexcstatus 1120311205 11204DCF 500B IV a a IV a a 055R0401A2440000