DCS 500 manual Incoming inspection, Storage and transport, Rating plate

Page 12

Chapter 1 - Introduction

Incoming inspection

After opening this package, you should check whether it contains

 

the following items:

 

DCS 500B / DCF 500B or DCP 500B thyristor power con-

 

verter in the configuration ordered

 

DCS 500B / DCF 500B or DCP 500B publications

 

Accessories, including manuals if ordered

 

Final test report

 

Check the consignment for any signs of damage. If you find any,

 

please contact the insurance company or the supplier.

 

Check the particulars given on the unit's rating plate to make sure

 

prior to installation and start-up that you have received the correct

 

unit type and unit version.

 

If the consignment is incomplete or contains any incorrect items,

 

please contact the supplier.

 

 

 

CAUTION! The thyristor power converter weighs quite a lot and

 

should therefore not be held by the front cover. Please put the unit

 

down only on its back (sizes C1/C2/A5). Always use care when

 

handling the unit, so as to avoid injuries or damage.

Storage and transport

 

If the unit had been in storage prior to installation or is transported

 

to another location, care must be taken to ensure that the environ-

 

mental conditions are complied with (see "System Descriptions

 

DCS 500B / DCF 500B or DCP 500B").

Rating plate

For purposes of identification, each thyristor power converter is fit-

 

ted with rating plates, stating the type code and the serial number,

 

which serve for each unit's individual identification.

 

The type code contains information on the characteristics and the

 

configuration of the unit. The first three digits of the serial number

 

refer to the year and week of manufacture. The last digits complete

 

the serial number so as to preclude two units receiving the same

 

type code and the same serial number.

 

The 112xx group provides information on the unit's software con-

 

figuration.

 

The technical data and specifications are valid as of going to press.

 

ABB reserves the right to make subsequent alterations.

 

If you have any questions concerning your drive system, please

 

contact your local ABB agent.

IV A 1 - 2

DCS 500B / DCP 500B Operating Instructions

3ADW000055R0401_DCS500B_Operating Instruction_e_d

Image 12
Contents DCS 500B / DCF 500B DCP 500B How the DCS 500 Documentation System works Operating Instructions DCS 500B / DCP 500B Operating Instructions Safety Instructions OverviewSafety Instructions Mains connection Emergency Stop buttons Intended use Contents Signals and Troubleshooting DCS 500B / DCP 500B Operating Instructions How to use this manual Contents of this manualTarget group Associated publicationsIncoming inspection Storage and transportRating plate General notes How this chapter is structuredRecommended motor voltages and field voltages = Line voltageMethod of functioning of the binary inputs DI5, DI7 and DI8 Symbols for enabling / disabling the reference System-dependent planningSymbol for displaying parameter values or connections Symbol for measuring physical variablesPreparatory work Scaling intra-unit signals 518 = 500 V fixed! rated power converter voltage Set this only for units of the DCP 500 series519 11202 = Save MOT1 SETPresetting the field supply unit 1305 = Field current for Under-excitation signalIV a 2 Adjusting the current controller 1201 = 3 Panel display ARM. AutotuningDCS 500B / DCP 500B Operating Instructions IV a 2 Speed feedback balancing Only when the e.m.f. signal is being used as speed feedback Balancing the field supply unit and the e.m.f. controller Continue with ChapterField weakening control with setting range 1 If the field time constant is not known 1204 = 1205 =11209 = 1201 = 0 Panel display not Activated 11202 = Save MOT1 SET 1002 =1004 = 1009 = 1010 =11003 = decrease so that motor voltage is 70%Proceed as described in 1. / 2. / 3. above = decrease so that motor voltage is 40%Only if analog tacho is used as speed feedback 12516 = increase slowly up to 20000 =100 % speed1708 = 0,1 s 1709 = 0,1 s 1204 POT1 = 10%...20% max. speed408 = desired response behaviour of controller 1008 = desired response behaviour of controller1204 = 1205 = Presetting the 3-phase field supply unit DCF 50xB 1201 = 5Panel display FEX2/3 Autotuning 3601 =3602 = 3603 =1201 = 4Panel display ARM. MAN. Tuning ⇒ CDP 310 or CDP ⇒ CDPStart Mode ID-NUMBER Total 1 DrivesACT Panel FunctionsPAR Drive Mode Pin/Parameter Selecting and Changing of ValueTo enter the Parameter Mode ValueSaving of the Parameters to backup memory BackupstoremodeFault Resetting Reset Display ModeFault History Display Uploading and Downloading of Parameters UPLOAD/DOWNLOAD DCSDCS 500B / DCP 500B Operating Instructions IV a 3 Setting of the Display Contrast Full Name of output pinsDisplay Mode release key Selecting output pins Drive Mode Running the Drive Operational Com- mand KeysSpeed Reference Setting for the Drive To enter the Reference SettingTo exit the Reference Setting ModeSignals and Troubleshooting Display of status, alarm and fault signalsStarting errors E General messagesFault Signals F Auxil. undervoltageConv.fan curr.fault Earth faultMotor 1 overtemp P418 SDCS-IOB-3, SDCS-POWExt.Overvolt.Fault Local & disconNected Limited by the activation of a free wheeling CircuitField ex.1 comerror Mains overvoltageCheck Parameters of Field Exciter Arm. curent ripple See Fault Code F No ext. FAN ackNo main cont. ack Field ex.1 not OKIV a 4 Reversal Fault Current DifferenceAlarm Signals a 103 Motor 1 temp. alarmCheck See Fault Code F 105 Conv. overtemp 101 Start inhibition108 110118 120127 128129 130134 136137 138At Macro x, macro-specific links or function Status Signals 11201Backupstoremode 11203 Fexcstatus11204 11205DCF 500B IV a a IV a a 055R0401A2440000