DCS 500 manual Act, Panel Functions

Page 39

3.3 Panel Functions

Actual Signal

Display Mode

ACT

Chapter 3 - Handling of Control Panel CDP 31x

The CDP 31x has four different keypad modes:

•Actual Signal Display Mode (ACT)

•Parameter Mode (PAR)

•Function Mode (FUNC)

•Drive Mode (DRIVE) for further extensions

This keypad mode will show, depending on the drive´s history:

•Actual Signals

•Faults

•Fault History Logger

If the ACT-key is pressed immediately after initialization this table is displayed. If no panel-key is touched for more than one minute the Actual Signal Display will appear automatically, except when Status display or speed reference setting is active. (see chapter 3.13 and 3.15)

Actual Signal Display

ID-number	Control	Speed	Main contactor	Run Status
of the Drive	Location	reference	status	I = RUN
	L = Local	rpm	0 = Open	0 = STOP

			= Remote				1 = Closed

	Statusrow
						0 L	0.0 rpm 00
	Actual Signal
						SPEED AC	0.0	rpm

	Name, value and unit					CONV CUR	0	A

	Cursor shows					U ARM AC	0	V

						_

the selected row

If a fault is effective in the drive, the Fault Display will appear auto- matically. This will happen with all other modes as well, except the Drive Mode is active.

Fault Display

			0 L	0.0	rpm 00
			DCS 500
			* FAULT *
Type of fault or alarm			No ext. FAN ack.
Type of fault or alarm			No ext. FAN ack.

To select Fault History Display see chapter 3.8

Fault History Display

1	= last fault				0	L	0.0	rpm 00

2	= second last fault			1		LAST FAULT
...
Fault or alarm name					I/O-Board not			found

Total time after
the power up				0000:14:12.64

HHHH:MM:SS.ss

DCS 500B / DCP 500B Operating Instructions

IV A 3 - 3

3ADW000055R0401_DCS500B_Operating Instruction_e_d

Image 39

Contents DCS 500B / DCF 500B DCP 500B How the DCS 500 Documentation System works Operating Instructions DCS 500B / DCP 500B Operating Instructions Overview Safety InstructionsSafety Instructions Mains connection Emergency Stop buttons Intended use Contents Signals and Troubleshooting DCS 500B / DCP 500B Operating Instructions Associated publications How to use this manualContents of this manual Target groupIncoming inspection Storage and transportRating plate = Line voltage General notesHow this chapter is structured Recommended motor voltages and field voltagesMethod of functioning of the binary inputs DI5, DI7 and DI8 System-dependent planning Symbols for enabling / disabling the referenceSymbol for measuring physical variables Symbol for displaying parameter values or connectionsPreparatory work Scaling intra-unit signals 11202 = Save MOT1 SET 518 = 500 V fixed! rated power converter voltageSet this only for units of the DCP 500 series 5191305 = Field current for Under-excitation signal Presetting the field supply unitIV a 2 1201 = 3 Panel display ARM. Autotuning Adjusting the current controllerDCS 500B / DCP 500B Operating Instructions IV a 2 Speed feedback balancing Only when the e.m.f. signal is being used as speed feedback Continue with Chapter Balancing the field supply unit and the e.m.f. controllerField weakening control with setting range 1 If the field time constant is not known 1204 = 1205 =11209 = 1009 = 1010 = 1201 = 0 Panel display not Activated 11202 = Save MOT1 SET1002 = 1004 == decrease so that motor voltage is 40% 11003= decrease so that motor voltage is 70% Proceed as described in 1. / 2. / 3. above12516 = increase slowly up to 20000 =100 % speed Only if analog tacho is used as speed feedback1008 = desired response behaviour of controller 1708 = 0,1 s 1709 = 0,1 s1204 POT1 = 10%...20% max. speed 408 = desired response behaviour of controller1204 = 1205 = Presetting the 3-phase field supply unit DCF 50xB 3603 = 1201 = 5Panel display FEX2/3 Autotuning3601 = 3602 =1201 = 4Panel display ARM. MAN. Tuning ⇒ CDP ⇒ CDP 310 or CDPID-NUMBER Total 1 Drives Start ModePanel Functions ACTPAR Pin/Parameter Selecting and Changing of Value Drive ModeValue To enter the Parameter ModeBackupstoremode Saving of the Parameters to backup memoryDisplay Mode Fault Resetting ResetFault History Display DCS Uploading and Downloading of Parameters UPLOAD/DOWNLOADDCS 500B / DCP 500B Operating Instructions IV a 3 Setting of the Display Contrast Full Name of output pinsDisplay Mode release key Selecting output pins Drive Mode Operational Com- mand Keys Running the DriveMode Speed Reference Setting for the DriveTo enter the Reference Setting To exit the Reference SettingDisplay of status, alarm and fault signals Signals and TroubleshootingGeneral messages Starting errors EAuxil. undervoltage Fault Signals FConv.fan curr.fault Earth faultMotor 1 overtemp SDCS-IOB-3, SDCS-POW P418Limited by the activation of a free wheeling Circuit Ext.Overvolt.FaultLocal & discon NectedField ex.1 comerror Mains overvoltageCheck Parameters of Field Exciter Arm. curent ripple Field ex.1 not OK See Fault Code FNo ext. FAN ack No main cont. ackIV a 4 Current Difference Reversal Fault101 Start inhibition Alarm Signals a103 Motor 1 temp. alarm Check See Fault Code F 105 Conv. overtemp120 108110 118130 127128 129138 134136 137At Macro x, macro-specific links or function 11201 Status SignalsBackupstoremode Fexcstatus 1120311205 11204DCF 500B IV a a IV a a 055R0401A2440000