Mitsubishi Electronics SDP-ECO 1630 III manual Operation precautions, Unacceptable

Page 17

Chapter 1 On Safety

1.5Operation precautions

Do not turn the machine's power supply ON or start operation until this manual has been thoroughly read and fully understood.

All operators must wear appropriate work clothing and should never wear necklaces, scarves, or other accessories which could be caught by moving parts and cause accidents.

Appropriate

Cap

Buttoned

Safety shoes (preferable)

Unacceptable

Gloves

(or wet hands) Always avoid clothing, gear, or accessories that could in any way

Open cuffs be caught up in the machine.

Loose or dangling necktie

Items hanging from clothes

Over-long trousers

Slippers or sandals

Do not operate the machine if you feel in anyway sick, nauseous or unsteady.

If you notice that the machine is in any way abnormal, immediately report the situation to your supervisor for appropriate action.

The SDP-Eco 1630 III can perform continuous automatic operation, but it must not be operated continuously without an operator in attendance.

An operator trained to take appropriate initial corrective actions should always be in attendance to deal immediately with any emergencies that may arise.

When your SDP-Eco 1630 III will not be operated for an extended period of time, be sure to unplug the power cord. Check for any dust or contamination in the outlet, power plug, and/or the AC power socket on your SDP-Eco 1630 III at least once a year.

During operation, do not open any of the unit's doors or covers. Opening these doors or covers may be hazardous to the safety of operators and other persons working in the vicinity, and may also damage the machine.

Power failure

If a power failure occurs due to an external reason, immediately turn OFF the power switch and the SDP-Eco 1630 III.

When power is recovered, supply power again, referring to "4.2 Turning ON the power switch".

- 9 -

Image 17
Contents Page III For Your Safety Compliance with Cispr Rules When export the machineCompliance with FCC Rules Limit of responsibilityIntroductory Note About this manual Contents Menus and panel displays When using the machine On SafetyPower supply Maintenance and safe passage during emergenciesSafety switches This machine incorporates a power supply unitSDP-Eco 1630 III is equipped with a leakage circuit breaker This machine incorporates high current electrical circuitsFor European model Hazard Safe handling method Types of warning labelsLocations of the machines warning labels are shown below Handling processing chemicals Processing chemical components Power cables Before connecting the power cableUnacceptable Operation precautionsSDP-Eco 1630 III Installation Precautions during transport and installationTransport and installation Installation environmentVentilation Installation space MaintenanceMachine disposal Page Main unit Names of Machine Components and PartsPage Operation panel Safety switch Handling plates Plate settingTwo set screws are Refer to 4.1 Cable Insert the plate edge until Plate end processing Page Cable connection check OperationPanel display flow after machine startup Turning on the power switchInitialization Press the Menu Key to display Amount using the key or Key and register the value with Local exposure ExposureRemote exposure Exposure Processing chemical replenishment Processor sectionPreparing and pouring processing chemical Preparing rinse water Processing chemical replacementIf the machine is not used for a long period Handling waste liquidCollecting exposed plates Turning OFF the power supply and inspection at shutdownOperation Page User menu Menus and panel displaysOperation status Remote mode display Power ON/OFF keyMenu/command selection Panel operationCommand execution Switch the mode between remote and localShift between commands Example Plate data User menuData channel Plate typeLaser setting Resolution settingLaser menu Remaining amount of plateLaser test exposure Punch specifications Mode menuPre. Feed menu Image Data menuRinse Maintenance menuKey Procedure In cases where the current values are changed toReplacement procedure MaintenanceCutter blade replacement Dust, clean it off with a blower Cylindrical lens cleaningFilter cleaning Punch dust removal Cleaning the processor rack Cleaning the processor sectionResetting the punch counter Processor rack Stay Re-attach the supply guides to the processor rack Cleaning the processing chemical tank and filterCleaning the processing chemical supply pipe Cleaning the nip roller and exit roller Upper Cleaning the exit roller lower Set screw Roller fixing bracket Washing tank Bearing for a roller Exit roller lower Cleaning the washing tank Left tray rail Set screw Around when you remove the hose Slide the washing tank Replacing the diffusion sheet SLM-EAC, SLM-EST Put the accompanying diffusion List of expendable parts How to order partsMonth Year SDP-Eco 1630 III Maintenance and Inspection Chart Message Displaying and clearing errorsMessage Message Operation status Status displayMessage Error contents List of error messagesME9 Removing Plate jam 1 Jam removal procedureRemoving Plate jam Basic specifications SpecificationsOverview diagram Silver Digiplater