Mitsubishi Electronics SDP-ECO 1630 III manual Plate end processing

Page 31

Chapter 3 Handling Plates

3.2 Plate end processing

When plate end is displayed, remove the plate and re-set a new one following the procedure below.

1)When <Plate End> is displayed on the panel:

The plate ended during exposure, so it is discharged from the processor.

Stop the buzzer by pressing the (reset) key.

After the plate is discharged, press the MENU key to shift to the local mode, and mount a new plate following the procedure mentioned in "3.1 Plate setting".

Cover for the plate removal port

Plate removal port

Note

Whether or not data will be

exposed

depends on

the

amount

of exposure

data

remaining when the plate end

is detected.

 

 

2) When

Pick up plate

is displayed

on the panel:

 

 

 

Plate ended at the beginning of an

exposure, so the remainder is

shorter

than

the

processor's

minimum transfer length. Please remove the plate.

1.Open the front door and remove the plate through the plate removal port.

2.Close the door and press the key to return to the local mode.

3.Re-set the plate following the procedure mentioned in "3.1 Plate setting".

- 23 -

Image 31
Contents Page III For Your Safety Limit of responsibility When export the machineCompliance with Cispr Rules Compliance with FCC RulesIntroductory Note About this manual Contents Menus and panel displays Maintenance and safe passage during emergencies On SafetyWhen using the machine Power supplyThis machine incorporates high current electrical circuits This machine incorporates a power supply unitSafety switches SDP-Eco 1630 III is equipped with a leakage circuit breakerFor European model Hazard Safe handling method Types of warning labelsLocations of the machines warning labels are shown below Handling processing chemicals Processing chemical components Power cables Before connecting the power cableUnacceptable Operation precautionsInstallation environment Precautions during transport and installationSDP-Eco 1630 III Installation Transport and installationVentilation Installation space MaintenanceMachine disposal Page Main unit Names of Machine Components and PartsPage Operation panel Safety switch Handling plates Plate settingTwo set screws are Refer to 4.1 Cable Insert the plate edge until Plate end processing Page Cable connection check OperationInitialization Turning on the power switchPanel display flow after machine startup Press the Menu Key to display Amount using the key or Key and register the value with Remote exposure ExposureLocal exposure Exposure Preparing and pouring processing chemical Processor sectionProcessing chemical replenishment Preparing rinse water Processing chemical replacementIf the machine is not used for a long period Handling waste liquidCollecting exposed plates Turning OFF the power supply and inspection at shutdownOperation Page User menu Menus and panel displaysOperation status Panel operation Power ON/OFF keyRemote mode display Menu/command selectionShift between commands Example Switch the mode between remote and localCommand execution Plate type User menuPlate data Data channelRemaining amount of plate Resolution settingLaser setting Laser menuLaser test exposure Image Data menu Mode menuPunch specifications Pre. Feed menuRinse Maintenance menuKey Procedure In cases where the current values are changed toCutter blade replacement MaintenanceReplacement procedure Dust, clean it off with a blower Cylindrical lens cleaningFilter cleaning Punch dust removal Resetting the punch counter Cleaning the processor sectionCleaning the processor rack Processor rack Stay Re-attach the supply guides to the processor rack Cleaning the processing chemical tank and filterCleaning the processing chemical supply pipe Cleaning the nip roller and exit roller Upper Cleaning the exit roller lower Set screw Roller fixing bracket Washing tank Bearing for a roller Exit roller lower Cleaning the washing tank Left tray rail Set screw Around when you remove the hose Slide the washing tank Replacing the diffusion sheet SLM-EAC, SLM-EST Put the accompanying diffusion List of expendable parts How to order partsMonth Year SDP-Eco 1630 III Maintenance and Inspection Chart Message Displaying and clearing errorsMessage Message Operation status Status displayMessage Error contents List of error messagesME9 Removing Plate jam 1 Jam removal procedureRemoving Plate jam Basic specifications SpecificationsOverview diagram Silver Digiplater