Mitsubishi Electronics SDP-ECO 1630 III manual Message, Displaying and clearing errors

Page 75

Chapter 8 Message

Chapter 8 Message

8.1 Message

The SDP-Eco 1630 III displays three kinds of messages: status messages, warning messages and error messages.

[Status message]

Status messages indicate the machine's current operation status.

[Warning message]

Warning messages indicate a problem which has no effect currently but may have adverse effects in the near future. These messages are displayed when the power is turned ON.

Pressing the key allows you to continue processing.

[Error message]

Error messages indicate a problem or error which is now occurring during operation. If an error message is displayed, a buzzer sounds and the machine

will not operate. Pressing the key while an error message is displayed stops the buzzer sound.

The following pages contain a listing of common error codes, their meanings, and corrective measures.

8.2 Displaying and clearing errors

When a problem or error occurs during operation, an error message is displayed on the display panel and all moving parts, such as the motor, stop. The machine will not operate while an error message is displayed.

[Error clearance]

Message

Contents

 

 

ME1

First, stop the buzzer sound by pressing the

key

ME2

and open the front door. After all required processes are

JAM1

completed, close the front door and press the

key.

JAM2

This clears the error message.

 

 

JAM3

*Do not turn OFF the main power when JAM1, JAM2,

 

JAM3 errors occur.

 

 

 

 

ME3

Turn the nip roller clearance handle until it is vertical

 

(locked) and then press the

key to reset the error.

Others

Eliminate the error with the

key.

 

 

 

 

 

- 67 -

Image 75
Contents Page III For Your Safety Limit of responsibility When export the machineCompliance with Cispr Rules Compliance with FCC RulesIntroductory Note About this manual Contents Menus and panel displays Maintenance and safe passage during emergencies On SafetyWhen using the machine Power supplyThis machine incorporates high current electrical circuits This machine incorporates a power supply unitSafety switches SDP-Eco 1630 III is equipped with a leakage circuit breakerFor European model Hazard Safe handling method Types of warning labelsLocations of the machines warning labels are shown below Handling processing chemicals Processing chemical components Power cables Before connecting the power cableUnacceptable Operation precautionsInstallation environment Precautions during transport and installationSDP-Eco 1630 III Installation Transport and installationVentilation Installation space MaintenanceMachine disposal Page Main unit Names of Machine Components and PartsPage Operation panel Safety switch Handling plates Plate settingTwo set screws are Refer to 4.1 Cable Insert the plate edge until Plate end processing Page Cable connection check OperationTurning on the power switch InitializationPanel display flow after machine startup Press the Menu Key to display Amount using the key or Key and register the value with Exposure Remote exposureLocal exposure Exposure Processor section Preparing and pouring processing chemicalProcessing chemical replenishment Preparing rinse water Processing chemical replacementIf the machine is not used for a long period Handling waste liquidCollecting exposed plates Turning OFF the power supply and inspection at shutdownOperation Page User menu Menus and panel displaysOperation status Panel operation Power ON/OFF keyRemote mode display Menu/command selectionSwitch the mode between remote and local Shift between commands ExampleCommand execution Plate type User menuPlate data Data channelRemaining amount of plate Resolution settingLaser setting Laser menuLaser test exposure Image Data menu Mode menuPunch specifications Pre. Feed menuRinse Maintenance menuKey Procedure In cases where the current values are changed toMaintenance Cutter blade replacementReplacement procedure Dust, clean it off with a blower Cylindrical lens cleaningFilter cleaning Punch dust removal Cleaning the processor section Resetting the punch counterCleaning the processor rack Processor rack Stay Re-attach the supply guides to the processor rack Cleaning the processing chemical tank and filterCleaning the processing chemical supply pipe Cleaning the nip roller and exit roller Upper Cleaning the exit roller lower Set screw Roller fixing bracket Washing tank Bearing for a roller Exit roller lower Cleaning the washing tank Left tray rail Set screw Around when you remove the hose Slide the washing tank Replacing the diffusion sheet SLM-EAC, SLM-EST Put the accompanying diffusion List of expendable parts How to order partsMonth Year SDP-Eco 1630 III Maintenance and Inspection Chart Displaying and clearing errors MessageMessage Message Operation status Status displayMessage Error contents List of error messagesME9 Removing Plate jam 1 Jam removal procedureRemoving Plate jam Basic specifications SpecificationsOverview diagram Silver Digiplater