Mitsubishi Electronics SDP-ECO 1630 III manual Pre. Feed menu, Image Data menu, Mode menu

Page 52

SDP-Eco1630 III USERS MANUAL

6.3 Pre. Feed menu

Whenever you set a new plate, a "Pre. Feed" operation is performed to eliminate any fogged sections at the leading edge.

From the display panel, you can select whether to feed 1 or 3 sheets for this operation. The length of each sheet is 500 mm, so if you perform a 3-sheet preliminary feed, 1500 mm of plate will be cut, fed and disposed of.

If there are still darkened or fogged areas on the plate, perform another preliminary feed.

6.4 Image Data menu

The SDP-Eco 1630 III incorporates a hard disk drive buffer to avoid idle time due to differences in calculation speed between itself and the host, and to enable quick re-exposure after an exposure was interrupted (e.g., if you use the stop key or the plate ends).

Data written in the hard disk drive can be exposed or erased in the local mode. Select the "Exposure" command to expose the data and the "Clear" command to erase it.

6.5 Mode menu

In this menu, you can operate the punch (option), select a dryer level, and set the buzzer response for different key operations.

Set the punch to ON to punch plates before image exposure or set it to OFF if punching is not necessary.

If the machine does not contain a punch unit, the "Un-mounted" message appears.

Punch specifications

Two types of punch unit options can be set: the DS punch (for alternately positionable punch) and the BELL punch.

Note

The distance between punch holes is fixed, so it is impossible to change the distance depending on the plate width.

386.5

Leading side

[DS punch]

φ5

220

5 x 8

Leading side

[BELL punch]

Dedicated for 335mm width plates

12 x 16

10 x 16

Cut line

- 44 -

Image 52
Contents Page III For Your Safety When export the machine Compliance with Cispr RulesCompliance with FCC Rules Limit of responsibilityIntroductory Note About this manual Contents Menus and panel displays On Safety When using the machinePower supply Maintenance and safe passage during emergenciesThis machine incorporates a power supply unit Safety switchesSDP-Eco 1630 III is equipped with a leakage circuit breaker This machine incorporates high current electrical circuitsFor European model Types of warning labels Hazard Safe handling methodLocations of the machines warning labels are shown below Handling processing chemicals Processing chemical components Before connecting the power cable Power cablesOperation precautions UnacceptablePrecautions during transport and installation SDP-Eco 1630 III InstallationTransport and installation Installation environmentVentilation Maintenance Installation spaceMachine disposal Page Names of Machine Components and Parts Main unitPage Operation panel Safety switch Plate setting Handling platesTwo set screws are Refer to 4.1 Cable Insert the plate edge until Plate end processing Page Operation Cable connection checkInitialization Turning on the power switchPanel display flow after machine startup Press the Menu Key to display Amount using the key or Key and register the value with Remote exposure ExposureLocal exposure Exposure Preparing and pouring processing chemical Processor sectionProcessing chemical replenishment Processing chemical replacement Preparing rinse waterHandling waste liquid If the machine is not used for a long periodTurning OFF the power supply and inspection at shutdown Collecting exposed platesOperation Page Menus and panel displays User menuOperation status Power ON/OFF key Remote mode displayMenu/command selection Panel operationShift between commands Example Switch the mode between remote and localCommand execution User menu Plate dataData channel Plate typeResolution setting Laser settingLaser menu Remaining amount of plateLaser test exposure Mode menu Punch specificationsPre. Feed menu Image Data menuMaintenance menu RinseProcedure In cases where the current values are changed to KeyCutter blade replacement MaintenanceReplacement procedure Cylindrical lens cleaning Dust, clean it off with a blowerFilter cleaning Punch dust removal Resetting the punch counter Cleaning the processor sectionCleaning the processor rack Processor rack Stay Cleaning the processing chemical tank and filter Re-attach the supply guides to the processor rackCleaning the processing chemical supply pipe Cleaning the nip roller and exit roller Upper Cleaning the exit roller lower Set screw Roller fixing bracket Washing tank Bearing for a roller Exit roller lower Cleaning the washing tank Left tray rail Set screw Around when you remove the hose Slide the washing tank Replacing the diffusion sheet SLM-EAC, SLM-EST Put the accompanying diffusion How to order parts List of expendable partsMonth Year SDP-Eco 1630 III Maintenance and Inspection Chart Message Displaying and clearing errorsMessage Status display Message Operation statusList of error messages Message Error contentsME9 Jam removal procedure Removing Plate jam 1Removing Plate jam Specifications Basic specificationsOverview diagram Silver Digiplater