Mitsubishi Electronics SDP-ECO 1630 III manual Re-attach the supply guides to the processor rack

Page 61

Chapter 7 Maintenance

Diffusion sheet

Brush bar

Diffusion sheet

SLM-EAC

SLM-EST

Note

If the diffusion sheet is curved or bent, loosen the sheet retainer on the processing chemical supply guide and replace the sheet with a stand-ard diffusion sheet.

9)Wash the processing chemical supply guide diffusion sheets (SLM-EAC x 2, SLM-EST x 1) with water and wipe them dry with a clean cloth.

10)Wash the processor rack and overflow tray with water.

Note

The synthetic rubber used for the processor rack roller is susceptible to high temperatures, so don't wash it with water that is warmer than 40˚C. Never use detergent or other cleaning solutions.

11)Re-attach the supply guides to the processor rack.

Cleaning the processing chemical tank and filter

Note

Upper cover

Always clean the processing chemical tank and filter when you replace the processing chemical every three months or after processing 1000m2 of plates.

1) Lift the upper cover for the processing tank and pull out the tank.

Processing tank

- The upper cover for SLM-EAC is attached to a panel heater, so it

Caution may be very hot. Be very careful when performing this operation.

- Sensor cords are connected to the upper cover. Do not forcibly pull at these cords.

- 53 -

Image 61
Contents Page III For Your Safety Compliance with Cispr Rules When export the machineCompliance with FCC Rules Limit of responsibilityIntroductory Note About this manual Contents Menus and panel displays When using the machine On SafetyPower supply Maintenance and safe passage during emergenciesSafety switches This machine incorporates a power supply unitSDP-Eco 1630 III is equipped with a leakage circuit breaker This machine incorporates high current electrical circuitsFor European model Hazard Safe handling method Types of warning labelsLocations of the machines warning labels are shown below Handling processing chemicals Processing chemical components Power cables Before connecting the power cableUnacceptable Operation precautionsSDP-Eco 1630 III Installation Precautions during transport and installationTransport and installation Installation environmentVentilation Installation space MaintenanceMachine disposal Page Main unit Names of Machine Components and PartsPage Operation panel Safety switch Handling plates Plate settingTwo set screws are Refer to 4.1 Cable Insert the plate edge until Plate end processing Page Cable connection check OperationInitialization Turning on the power switchPanel display flow after machine startup Press the Menu Key to display Amount using the key or Key and register the value with Remote exposure ExposureLocal exposure Exposure Preparing and pouring processing chemical Processor sectionProcessing chemical replenishment Preparing rinse water Processing chemical replacementIf the machine is not used for a long period Handling waste liquidCollecting exposed plates Turning OFF the power supply and inspection at shutdownOperation Page User menu Menus and panel displaysOperation status Remote mode display Power ON/OFF keyMenu/command selection Panel operationShift between commands Example Switch the mode between remote and localCommand execution Plate data User menuData channel Plate typeLaser setting Resolution settingLaser menu Remaining amount of plateLaser test exposure Punch specifications Mode menuPre. Feed menu Image Data menuRinse Maintenance menuKey Procedure In cases where the current values are changed toCutter blade replacement MaintenanceReplacement procedure Dust, clean it off with a blower Cylindrical lens cleaningFilter cleaning Punch dust removal Resetting the punch counter Cleaning the processor sectionCleaning the processor rack Processor rack Stay Re-attach the supply guides to the processor rack Cleaning the processing chemical tank and filterCleaning the processing chemical supply pipe Cleaning the nip roller and exit roller Upper Cleaning the exit roller lower Set screw Roller fixing bracket Washing tank Bearing for a roller Exit roller lower Cleaning the washing tank Left tray rail Set screw Around when you remove the hose Slide the washing tank Replacing the diffusion sheet SLM-EAC, SLM-EST Put the accompanying diffusion List of expendable parts How to order partsMonth Year SDP-Eco 1630 III Maintenance and Inspection Chart Message Displaying and clearing errorsMessage Message Operation status Status displayMessage Error contents List of error messagesME9 Removing Plate jam 1 Jam removal procedureRemoving Plate jam Basic specifications SpecificationsOverview diagram Silver Digiplater